A new Rococo 2 X-ray fluorescence detector was implemented into the cryogenic sample environment at the Hard X-ray Micro/Nano-Probe beamline P06 at PETRA III, DESY, Hamburg, Germany. A four sensor-field cloverleaf design is optimized for the investigation of planar samples and operates in a backscattering geometry resulting in a large solid angle of up to 1.1 steradian. The detector, coupled with the Xspress 3 pulse processor, enables measurements at high count rates of up to 106 counts per second per sensor. The measured energy resolution of ∼129 eV (Mn Kα at 10000 counts s−1) is only minimally impaired at the highest count rates. The resulting high detection sensitivity allows for an accurate determination of trace element distributions such as in thin frozen hydrated biological specimens. First proof-of-principle measurements using continuous-movement 2D scans of frozen hydrated HeLa cells as a model system are reported to demonstrate the potential of the new detection system.

A simple and robust tool for spatio-temporal overlap of THz and XUV pulses in in-vacuum pump–probe experiments is presented. The technique exploits ultrafast changes of the optical properties in semiconductors (i.e. silicon) driven by ultrashort XUV pulses that are probed by THz pulses. This work demonstrates that this tool can be used for a large range of XUV fluences that are significantly lower than when probing by visible and near-infrared pulses. This tool is mainly targeted at emerging X-ray free-electron laser facilities, but can be utilized also at table-top high-harmonics sources.

A new setup for picosecond pump–probe X-ray scattering at the Austrian SAXS beamline at Elettra-Sincrotrone Trieste is presented. A high-power/high-repetion-rate laser has been installed on-site, delivering UV/VIS/IR femto­second-pulses in-sync with the storage ring. Data acquisition is achieved by gating a multi-panel detector, capable of discriminating the single X-ray pulse in the dark-gap of the Elettra hybrid filling mode. Specific aspects of laser- and detection-synchronization, on-line beam steering as well protocols for spatial and temporal overlap of laser and X-ray beam are also described. The capabilities of the setup are demonstrated by studying transient heat-transfer in an In/Al/GaAs superlattice structure and results are confirmed by theoretical calculations.

Bone crystallite chemistry and structure change during bone maturation. However, these properties of bone can also be affected by limited uptake of the chemical constituents of the mineral by the animal. This makes probing the effect of bone-mineralization-related diseases a complicated task. Here it is shown that the combination of vibrational spectroscopy with two-dimensional X-ray diffraction can provide unparalleled information on the changes in bone chemistry and structure associated with different bone pathologies (phosphate deficiency) and/or health conditions (pregnancy, lactation). Using a synergistic analytical approach, it was possible to trace the effect that changes in the remodelling regime have on the bone mineral chemistry and structure in normal and mineral-deficient (hypophosphatemic) mice. The results indicate that hypophosphatemic mice have increased bone remodelling, increased carbonate content and decreased crystallinity of the bone mineral, as well as increased misalignment of crystallites within the bone tissue. Pregnant and lactating mice that are normal and hypophosphatemic showed changes in the chemistry and misalignment of the apatite crystals that can be related to changes in remodelling rates associated with different calcium demand during pregnancy and lactation.

A few images of comet 67P/Churyumov-Gerasimenko just sent back by the European spaceship Rosetta appear to be a snowboarder’s dream: pristine slopes covered in powder. […]

The post Comet probe set to answer ancient question of life on earth appeared first on Smithsonian Insider.

How did the universe begin? And what came before the Big Bang? Cosmologists have asked these questions ever since discovering that our universe is expanding. […]

The post Theorists Propose a New Method to Probe the Beginning of the Universe appeared first on Smithsonian Insider.

NASA’s InSight probe, scheduled to land on the surface of Mars in November 2018, will be boring. Boring a hole, that is. It will drill […]

The post ISO: a boring Martian landing spot for NASA’s InSight probe appeared first on Smithsonian Insider.

The search for extraterrestrial intelligence has looked for many different signs of alien life, from radio broadcasts to laser flashes, without success. However, newly published […]

The post Could Fast Radio Bursts Be Powering Alien Probes? appeared first on Smithsonian Insider.

The center of our Galaxy has been intensely studied for many years, but it still harbors surprises for scientists. A snake-like structure lurking near our […]

The post Cosmic filament probes our galaxy’s giant black hole appeared first on Smithsonian Insider.

Smithsonian scientists have joined NASA and other organizations this summer to do something incredible: launch a spacecraft, the Parker Solar Probe, into space and have […]

The post A solar probe is on its way to touch the sun. The Smithsonian built the tool that will measure the sun without melting appeared first on Smithsonian Insider.

Rick Bright filed a complaint this week with the Office of Special Counsel, a government agency responsible for whistleblower complaints.; Credit: /Public Health Emergency via AP

Attorneys for Rick Bright, the government scientist who said he had been reassigned and subsequently filed a whistleblower complaint, say a government watchdog agrees that he should be reinstated to his post.

Bright was serving as director of the Biomedical Advanced Research and Development Authority, which is working on a vaccine to combat the coronavirus.

He said he was ousted from the position last month because he wanted to spend money on safe and vetted treatments for COVID-19 — not on ones without "scientific merit," such as hydroxychloroquine, the anti-malarial drug that President Trump and others had been touting.

Trump on Wednesday called Bright "a disgruntled employee who's trying to help the Democrats win an election."

Bright's attorneys say that the Office of Special Counsel, which hears whistleblower cases, determined there were "reasonable grounds" to believe that his removal was retaliatory and therefore prohibited.

Bright's attorneys say OSC plans to contact the Department of Health and Human Services to request that it put Bright's removal on hold for 45 days so the office can complete its investigation into the allegations.

The OSC said it "cannot comment on or confirm the status of open investigations."

In a statement to NPR, Caitlin Oakley, a spokesperson for HHS, said: "This is a personnel matter that is currently under review. However, HHS strongly disagrees with the allegations and characterizations in the complaint from Dr. Bright."

This content is from Southern California Public Radio. View the original story at SCPR.org.

Rick Bright filed a complaint this week with the Office of Special Counsel, a government agency responsible for whistleblower complaints.; Credit: /Public Health Emergency via AP

Attorneys for Rick Bright, the government scientist who said he had been reassigned and subsequently filed a whistleblower complaint, say a government watchdog agrees that he should be reinstated to his post.

Bright was serving as director of the Biomedical Advanced Research and Development Authority, which is working on a vaccine to combat the coronavirus.

He said he was ousted from the position last month because he wanted to spend money on safe and vetted treatments for COVID-19 — not on ones without "scientific merit," such as hydroxychloroquine, the anti-malarial drug that President Trump and others had been touting.

Trump on Wednesday called Bright "a disgruntled employee who's trying to help the Democrats win an election."

Bright's attorneys say that the Office of Special Counsel, which hears whistleblower cases, determined there were "reasonable grounds" to believe that his removal was retaliatory and therefore prohibited.

Bright's attorneys say OSC plans to contact the Department of Health and Human Services to request that it put Bright's removal on hold for 45 days so the office can complete its investigation into the allegations.

The OSC said it "cannot comment on or confirm the status of open investigations."

In a statement to NPR, Caitlin Oakley, a spokesperson for HHS, said: "This is a personnel matter that is currently under review. However, HHS strongly disagrees with the allegations and characterizations in the complaint from Dr. Bright."

This content is from Southern California Public Radio. View the original story at SCPR.org.

After blowing its first chance to orbit Venus two years ago, Japan's Akatsuki spacecraft is ready for a comeback in 2015, mission scientists say.

Residents of Pennsylvania's top natural gas-producing town will soon know what may be lurking in their drinking water wells. Federal environmental regulators ar

A NASA spacecraft's epic Pluto encounter is officially underway.

NASA's New Horizons spacecraft has snapped new images of Pluto — the first taken by the probe during its six-month approach to the dwarf planet.

Pluto looks especially welcoming in a new photo by NASA's approaching New Horizons probe.

A NASA spacecraft slammed into the surface of Mercury on Thursday, April 30, bringing a groundbreaking mission to a dramatic end.

U.S. authorities have largely suspended their investigation of the molasses spill that fouled Hawaiian waters last month.

An innovative concept for tiny probes attached to gliders could one day allow small robots to explore intricate locales on Mars.

Examining layers of offshore sediment can provide insight into the link between glaciers and climate change.

After landing rovers and its spacecraft on the surface of asteroid Ryugu, JAXA is returning with a sample.

New York state's top prosecutor on Thursday announced that the company Zoom would improve security measures, after flaws were detected as the video conferencing platform soared in popularity amid the coronavirus pandemic.

read more

AirAsia CEO Tony Fernandes steps aside amid bribery probe

Amazon files writ petition in K'taka HC seeking stay on CCI probe order

The Railways has ordered a comprehensive probe into the Aurangabad accident in which 16 migrants workers who were sleeping on the tracks were mowed down by a goods train early on Friday.

"The identification of this male is of vital importance to this investigation"

Heterocyclic compounds of formula (I) useful as imaging probes of Tau pathology in Alzheimer's disease are described. Compositions and methods of making such compounds are also described.

The present disclosure relates to a sulfonated benzene compound emitting fluorescence by reaction with hydrogen peroxide, aqueous-dispersed fluorescent nanoprobes applicable for real-time detection of hydrogen peroxide, and a fluorescent nanoprobe fabrication method. The fluorescent nanoprobe contains the following sulfonated benzene compound and water.

An apparatus and method for indicating locus of an ultrasonic probe configured to transmit and receive ultrasonic waves toward a part of a subject wherein a position or movement of the ultrasonic probe is detected, and a locus of the ultrasonic probe on an image of the part of the subject is indicated according to the detected position or movement.

Electrochemical corrosion potential (ECP) probe assemblies may be used to monitor ECP of materials due to coolant chemistry in an operating nuclear reactor. Example embodiment assemblies include at least one ECP probe that detects ECP of potentially several different materials, a structural body providing a fluid flow path for the coolant over the ECP probes, and a signal transmitter that transmits or carries ECP data to an external receiver. The ECP probes may be of any number and/or type, so as to detect ECP for different component materials, including stainless steel, a zirconium alloys, etc. The ECP probes may further detect ECP due to ion concentration, pH, etc. The ECP data may be transmitted through wired or wireless signal transmitters. Example methods include installing and using example embodiment ECP probe assemblies in nuclear reactors and facilities.

A method and apparatus for the calibration of neutron flux monitoring devices used in a nuclear reactor core. The apparatus includes a transverse in-core probe (TIP) cable with a neutron absorber located a fixed distance apart from a TIP detector. The neutron absorber may be passed within close proximity of the neutron flux monitoring device such that a perceived drop in measured neutron flux occurs, whereupon the cable may be repositioned relative to the monitoring device to ensure that the TIP detector is within close proximity of the monitoring device for purposes of calibrating the monitoring device.

A spatially-aware radiation probe system/method allowing for detection and correction of radiation readings based on the position and/or movement of a radiation detector is disclosed. The system incorporates a radiation detector combined with a spatially-aware sensor to permit detection of spatial context parameters associated with the radiation detector and/or object being probed. This spatial context information is then used by analysis software to modify the detected radiation values and/or instruct the radiation probe operator as to appropriate measurement activity to ensure accurate radiation measurements. The spatially-aware sensor may include but is not limited to: distance sensors to determine the distance between the radiation detector and the object being monitored; accelerometers integrated within the radiation detector to detect movement of the radiation detector; and/or axial orientation sensors to determine the axial orientation of the radiation detector.

A power combiner/divider having a waveguide, a plurality of amplifiers disposed on a supporting structure, a plurality of probes, each one having a first end electrically coupled to an output of a corresponding one of the plurality of amplifiers and a second end projecting outwardly from the supporting structure and into the waveguide. The probes are disposed in a common region of the waveguide. The region has a common electric field maximum within the waveguide. A first portion of the probes proximate the sidewalls have lengths different from a second portion of the probes disposed in a region distal from the sidewalls of the waveguide. The waveguide is supported by the support structure. The power combiner is a monolithic microwave integrated circuit structure.

An exemplary surgical probe and methods of making the same are disclosed. An exemplary surgical probe may include a tubular body and a scissor assembly received at least partially within the body. The scissor assembly may include a first blade fixed to the tubular body that includes a body portion and an end portion. The scissor assembly may further include a second blade that is configured to move longitudinally within the tubular body. The body portions of the first and second blades may each define respective cross sections normal to a longitudinal axis of the tubular body. The cross sections may each define centrally disposed edges adjacent one another, and the cross sections may each be asymmetrical about a line substantially parallel to the centrally disposed edges.

A probe deployment mechanism of a coordinate measuring machine provides for extending and retracting a probe. The probe is displaceable with respect to the actuator body connected to the measuring machine. A locator coupling secures the probe to the actuator body at the extended position for taking measurements. A drive coupled to the probe displaces the probe between the extended and retracted positions but at the extended position, the drive is releasable from the probe for kinetically isolating the locator coupling.

A touch probe (1; 1'; 1″; 1'″) for applications in machine tools or measuring machines includes a support frame (2) with a protective casing (3), and a movable armset (5) with a feeler (11) to touch a part to be checked (13). The probe includes a detection device (23) with a laminar piezoelectric transducer (25) made of polymeric material, such as polyvinylidene fluoride, which is connected to the support frame and fixed at a bearing and locating area (7), on which the movable armset rests in a position defined by an isostatic rest system (17). Conditioning electronics (30) connected to the support frame include processing means for processing a force signal (M) provided by the detection device, comparing it with a threshold value (S) and generating a touch signal (T). The conditioning electronics include differential charge amplifiers (3) and a processing system (55) to dynamically vary the threshold value depending on the most recent values of the force signal detected.

In a method for calibrating a star probe of an image measuring machine, the star probe includes one or more probe heads. Probe configuration information for the star probe is configured when there is no probe configuration file of the star probe stored in a storage device of the image measuring machine, and one of the probe heads to be calibrated is selected from the star probe. The method calibrates a radius value of the selected probe head, and calibrates the deviation between the center point of the selected probe head and the focus of the camera lens. The method further generates a star probe model of the star probe according to the probe configuration information and the probe calibration information, and displays the star probe model of the star probe on a display device of the image measuring machine.

A force biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a first plunger member reciprocally mounted in the internal cavity proximate the lower end of the internal cavity. A spring member is positioned in the internal cavity between the plunger member and the second end of the internal cavity. Three or more conductive bearings are positioned in the internal cavity in contact with the first plunger member and the spring member. A force biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a first plunger member reciprocally mounted in the internal cavity proximate the lower end of the internal cavity and a second plunger member reciprocally mounted in the internal cavity proximate the upper end of the internal cavity. A spring member is positioned in the internal cavity between the first plunger member and the second plunger member. Three or more conductive bearings are positioned in the internal cavity in contact with the first plunger member and the spring member.

A force-biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a first plunger member reciprocally mounted in the internal cavity proximate the lower end of the internal cavity. A spring member is positioned in the internal cavity between the plunger member and the second end of the internal cavity. At least one cavity formed in the plunger member with a conductive bearing in the cavity in electrical contact with the plunger and with the wall of the barrel member. A force-biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a first plunger member reciprocally mounted in the internal cavity proximate the lower end of the internal cavity and a second plunger member reciprocally mounted in the internal cavity proximate the upper end of the internal cavity. A spring member is positioned in the internal cavity between the first plunger member and the second plunger member. At least one cavity formed in the first plunger member with a first conductive bearing in the cavity in electrical contact with the first plunger and with the wall of the barrel member and at least one cavity formed in the second plunger member with a second conductive bearing in the cavity in electrical contact with the second plunger and with the wall of the barrel member.

A force-biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a first plunger member reciprocally mounted in the internal cavity proximate the lower end of the internal cavity. A spring member is positioned in the internal cavity between the plunger member and the second end of the internal cavity. At least one rectangular cavity formed in the plunger member with a movable cylindrical bearing in the cavity that applies a slight transverse force to the plunger member ensuring good electrical contact between the plunger and the wall of the barrel member. A force-biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a first plunger member reciprocally mounted in the internal cavity proximate the lower end of the internal cavity and a second plunger member reciprocally mounted in the internal cavity proximate the upper end of the internal cavity. A spring member is positioned in the internal cavity between the first plunger member and the second plunger member. At least one rectangular cavity formed in the first plunger member with a first movable cylindrical bearing in the cavity that applies a slight transverse force to the first plunger member ensuring good electrical contact between the first plunger member and the wall of the barrel member and at least one rectangular cavity formed in the second plunger member with a second movable cylindrical bearing in the cavity that applies a slight transverse force to the second plunger member ensuring good electrical contact between the second plunger member and the wall of the barrel member

A force biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a split plunger member comprised of an upper split plunger part separated from a lower split plunger part separated by a diagonal cut reciprocally mounted in the internal cavity proximate the lower end of the internal cavity. A spring member is positioned in the internal cavity between the upper split plunger part and the second end of the internal cavity. A force biased spring probe pin assembly includes a barrel member having a barrel wall defining an elongate internal cavity with a lower end and an upper end. The assembly also includes a first split plunger member reciprocally mounted in the internal cavity proximate the lower end of the internal cavity and a second split plunger member reciprocally mounted in the internal cavity proximate the upper end of the internal cavity. The first and second split plunger members are each comprised of two parts: a first upper plunger part separated from a first lower plunger part by a diagonal cut. A spring member is positioned in the internal cavity between the first and second upper split plunger parts. In each split plunger the diagonal surface of the upper split plunger part exerts a transverse force to the diagonal surface of the lower split plunger part ensuring good electrical contact between the lower split plunger member part and the barrel wall.

A probe card, a wafer testing system and a wafer testing method are provided. The wafer testing system includes a wafer holder and a probe card. A wafer is held on the wafer holder, and testing pads are formed on the wafer, in which the testing pads are arranged along a test straight line. The probe card includes probes each of which includes an arm portion and a tip portion. An included angle between the test straight line and an extension of a projection line of the arm portion onto the wafer ranges from about 40 degrees to about 55 degrees.

Attorneys for Rick Bright, the government scientist who said he had been reassigned and subsequently filed a whistleblower complaint , say a government watchdog agrees that he should be reinstated to his post. Bright was serving as director of the Biomedical Advanced Research and Development Authority, which is working on a vaccine to combat the coronavirus. He said he was ousted from the position last month because he wanted to spend money on safe and vetted treatments for COVID-19 — not on ones without "scientific merit," such as hydroxychloroquine, the anti-malarial drug that President Trump and others had been touting. Trump on Wednesday called Bright "a disgruntled employee who's trying to help the Democrats win an election." Bright's attorneys say that the Office of Special Counsel, which hears whistleblower cases, determined there were "reasonable grounds" to believe that his removal was retaliatory and therefore prohibited. Bright's attorneys say OSC plans to contact the