Register now: 8 March 2018
A webinar sponsored by HORIBA Scientific

A tandem-double-slit optical system was constructed to evaluate the practical beam emittance of undulator radiation. The optical system was a combination of an upstream slit (S1) and downstream slit (S2) aligned on the optical axis with an appropriate separation. The intensity distribution after the double slits, I(x1, x2), was measured by scanning S1 and S2 in the horizontal direction. Coordinates having 1/sqrt e intensity were extracted from I(x1, x2), whose contour provided the standard deviation ellipse in the x1–x2 space. I(x1, x2) was converted to the corresponding distribution in the phase space, I(x1, x1'). The horizontal beam emittance was evaluated to be 3.1 nm rad, which was larger than the value of 2.4 nm rad estimated by using ray-tracing. It was found that the increase was mainly due to an increase in beam divergence rather than size.

Enhancement of X-ray excited optical luminescence in a 100 µm-thick diamond plate by introduction of defect states via electron beam irradiation and subsequent high-temperature annealing is demonstrated. The resulting X-ray transmission-mode scintillator features a linear response to incident photon flux in the range 7.6 × 108 to 1.26 × 1012 photons s−1 mm−2 for hard X-rays (15.9 keV) using exposure times from 0.01 to 5 s. These characteristics enable a real-time transmission-mode imaging of X-ray photon flux density without disruption of X-ray instrument operation.

The Sun’s outer atmosphere, or corona, has posed an enduring mystery. Why is it so hot? The Sun’s visible surface is only 10,000 degrees Fahrenheit, […]

The post Sun’s loops are displaying an optical illusion appeared first on Smithsonian Insider.

The structural and nonlinear optical properties of a new anilinium hybrid crystal of chemical formula (C6H7NCl+·NO3−)3 have been investigated. The crystal structure was determined from single-crystal X-ray diffraction measurements performed at a temperature of 100 K which show that the compound crystallizes in a noncentrosymmetric space group (Pna21). The structural analysis was coupled with Hirshfeld surface analysis to evaluate the contribution of the different intermolecular interactions to the formation of supramolecular assemblies in the solid state that exhibit nonlinear optical features. This analysis reveals that the studied compound is characterized by a three-dimensional network of hydrogen bonds and the main contributions are provided by the O...H, C...H, H...H and Cl...H interactions, which alone represent ∼85% of the total contributions to the Hirshfeld surfaces. It is noteworthy that the halogen...H contributions are quite comparable with those of the H...H contacts. The nonlinear optical properties were investigated by nonlinear diffuse femtosecond-pulse reflectometry and the obtained results were compared with those of the reference material LiNbO3. The hybrid crystals exhibit notable second (SHG) and third (THG) harmonic generation which confirms its polarity is generated by the different intermolecular interactions. These measurements also highlight that the THG signal of the new anilinium compound normalized to its SHG counterpart is more pronounced than for LiNbO3.

The federal government should foster collaboration and decrease obstacles that can keep foreign atomic, molecular, and optical (AMO) physicists from working in the United States, if the nation is to maintain its position as leader in these fields, says a new report from the National Academies of Sciences, Engineering, and Medicine.

Experts of Paleolithic art in France say some cave drawings have a reoccurring theme.

Even if printing is distorted or unclear due to conveyor line conditions, a unique reading method with a built-in dictionary enables stable reading of characters.(FQ2-CH Series)

All About Eyewear Optical specializes in distributing brand name eyewear and providing excellent service, servicing the Bedford, Nova Scotia and Halifax, Nova Scotia region. All About Eyewear Optical wins its first Consumer Choice Award.

In 2018, KOIA had arranged consultation worth 2.5 million USD and signed contracts worth 500 thousand USD in OPTI and export consultation in Poland, and it is anticipating for a great outcome in the export consultation this time in the Netherlands.

Just-Released CIR AOC Report

The sessions are open to the anyone interested in learning more about how CIR views these market opportunities

Disclosed is a method for preparing optically pure (+)-ambrisentan and (+)-darusentan, comprising: firstly catalyzing the asymmetric epoxidation of a β-unsaturated alkene using a chiral ketone derived from fructose or a hydrate thereof as a catalyst, and then subjecting the product to an epoxy compound ring-opening reaction and substitution reaction successively to obtain optically pure (+)-ambrisentan and (+)-darusentan.

This optical glass contains, as represented by mol %, 18 to 38% P2O5, 0 to 15% B2O3, 23 to 40% P2O5+B2O3, 4 to 28% Nb2O5, 0 to 20% TiO2, 10 to 30% Nb2O5+TiO2, 15 to 35% Li2O+Na2O+K2O, and 21 to 38% ZnO, but does not contain BaO, WO3, Bi2O3 or SiO2, and the ratio of the mol % of ZnO to the total mol % of Li2O+Na2O+K2O (i.e., ZnO/(Li2O+Na2O+K2O)) is 0.8 to 2.0.

A highly refractive and highly transparent optical glass is provided. The use of such a glass, optical elements and processes for producing the glass or the optical elements are also provided.

Provided is an optical glass that has desired optical properties, superior resistance to devitrification, and superior mass productivity. An optical glass is made of a SiO2—Nb2O5—TiO2-based glass having a refractive index (nd) of 1.75 to 1.95 and an Abbe's number (νd) of 15 to 35 and has an operation temperature range (ΔT=(temperature at 100.5 poise)−(liquidus temperature)) of 20° C. or more. The optical glass preferably contains, in percent by mass, 15% to 45% SiO2, 15% to 40% (but excluding 40%) Nb2O5 and 1% to 30% TiO2 as glass components.

An optical glass including B3+, La3+ and Nb5+ as cationic components constituting the glass, wherein the optical glass satisfies the following expressions represented in cation percentages: 10 cat. %≦B3+≦50 cat. %;40 cat. %≦La3+≦65 cat. %;0 cat. %≦Nb5+≦40 cat. %;80 cat. %≦(total amount of B3++La3++Nb5+)≦100 cat. %; and0 cat. %≦Si4+≦10 cat. %;0 cat. %≦Ge4+≦5 cat. %;0 cat. %≦Mg2+≦5 cat. %;0 cat. %≦Ba2+≦10 cat. %;0 cat. %≦Ca2+≦10 cat. %;0 cat. %≦Sr2+≦10 cat. %;0 cat. %≦Zn2+≦20 cat. %;0 cat. %≦W6+≦5 cat. %;0 cat. %≦Zr4+≦5 cat. %;0 cat. %≦Ti4+≦5 cat. %;0 cat. %≦Bi3+≦5 cat. %;0 cat. %≦Ta5+≦10 cat. %;0 cat. %≦(total amount of Y3++Gd3+)≦20 cat. %; and0 cat. %≦(total amount of Yb3++Lu3+)≦10 cat. %.

A nanostructure, an optical device including the nanostructure, and methods of manufacturing the nanostructure and the optical device. A method of manufacturing a nanostructure may include forming a block copolymer template layer and a precursor pattern of metal coupled to the block copolymer template layer on a graphene layer, and forming a metal nanopattern on the graphene layer by removing the block copolymer template layer and reducing the precursor pattern.

In certain embodiments novel nanoparticles (nanowontons) are provided that are suitable for multimodal imaging and/or therapy. In one embodiment, the nanoparticles include a first biocompatible (e.g., gold) layer, an inner core layer (e.g., a non-biocompatible material), and a biocompatible (e.g., gold) layer. The first gold layer includes a concave surface that forms a first outer surface of the layered nanoparticle. The second gold layer includes a convex surface that forms a second outer surface of the layered nanoparticle. The first and second gold layers encapsulate the inner core material layer. Methods of fabricating such nanoparticles are also provided.

Described herein are devices, compositions, and methods for improving color discernment.

The present disclosure relates to a thermally resistant optical siloxane resin composition including siloxane containing photo-cationically polymerizable epoxy group, a photo initiator, and an antioxidant.

An optical component and an electrical board that have a low coefficient of linear expansion and small mold shrinkage, a method for producing the optical component, and a method for producing the electronic board are provided. An optical component includes a polymer having a repeating structural unit represented by general formula (1) where R1 and R2 each independently represent —H or —CH3; m and n each independently represent an integer in the range of 0 to 3; asterisk denotes a dangling bond that bonds to one of Xa and Xb; and —H bonds to the other one of Xa and Xb.

A heat-resistant cured product is efficiently produced by obtaining a semi-cured product where a curable resin composition containing a (meth)acrylate monomer, a non-conjugated vinylidene group-containing compound and a thermal radical-polymerization initiator is processed by at least one of photoirradiation and heating to give a semi-cured product having a complex viscosity of from 105 to 108 mPa·s at 25° C. and at a frequency of 10 Hz; and putting the semi-cured product in a forming die for pressure formation therein, and heating it therein for thermal polymerization to give a cured product.

An optically active bisbenzyl compound or a racemic bisbenzyl compound represented by formula (2) that has axial chirality: where: R1 represents a halogen, or an optionally substituted: linear, branched, or cyclic C1-8 alkyl, C2-8 alkenyl, C2-8 alkynyl, C6-14 aryl, C3-8 heteroaryl, linear, branched, or cyclic C1-8 alkoxy, or C7-16 aralkyl;R21 each independently represents hydrogen, halogen, nitro, or an optionally substituted: linear, branched, or cyclic C1-8 alkyl, C2-8 alkenyl, C2-8 alkynyl, C6-14 aryl, linear, branched, or cyclic C1-8 alkoxy, or a C7-16 aralkyl;R3 represents hydrogen, or an optionally substituted: C6-14 aryl, a C3-8 heteroaryl, or a C7-16 aralkyl; andY2 represents a halogen, or an optionally substituted: C1-8 alkylsulfonyloxy, C6-14 arylsulfonyloxy, or C7-16 aralkylsulfonyloxy.

An optically active bicyclic compound is efficiently produced by optical resolution using an optically active amine.

Accessory for a laptop computer with LCD display which is connected to the laptop serial communications port and optically transmits data to a portable information device, such as a wristwatch designed to receive data as sequential pulses of light. The accessory includes a microcomputer with an RC timebase which is calibrated each time it is used by a special internal program, so that the input baud rate to the accessory matches the communications baud rate of the data received from the laptop. The internal program also permits selection of an output baud rate for the optically transmitted data.

An optical backup apparatus is provided and includes an optical storage device, an interface module to connect with at least one type of external storage medium, and a control unit to back up data from the external storage medium to the optical storage device in response to an external remote control operation.

The polycyclic organic compounds which are substantially transparent for an electromagnetic radiation in the visible spectral range, an anisotropic optical film comprising at least one polycyclic organic compound and a method of producing thereof are disclosed. The polycyclic organic compounds have a general formula (I) wherein A and B are acid groups, n is the number of phenyl rings in the range from 3 to 10; m is 0, 1, 2 or 3; l is 1, 2, or 3, p is 1, 2, 3, 4, 5 or 6, C is a counterion from a list comprising H+, NH+4, Na+, K+, Li+, Cs+, Ca2+, Mg2+, Sr2+, La3+, Zn2+, Zr4+, Ce3+, Y3+, Yb3+, Gd3+, and any combination thereof; k is the number of counterions necessary for compensation of the negative electric charge equal to (−p).

An optical disc drive (ODD) includes a radio-frequency identification (RFID) reader. The reader includes a circuit and a coil antenna which has a rotational symmetry with respect to a rotation axis of a motor, shaft and turntable of the ODD. The coil antenna can be secured to a wall of a housing of the ODD or around the motor and/or shaft. The reader can read an RFID tag on an optical disc. The RFID tag includes a circuit and a coil antenna which has a rotational symmetry with respect to the disc. As a result, the RFID tag can be read while the disc is rotating. A magnetic insulating material such as a ferrite polymer composite film is used to magnetically insulate the coil antenna. An authentication code can be read from the RFID tag to control access to content of the optical disc.

Provided is a pressure-sensitive adhesive for polarizing plates which can adhere a polarizing plate on a liquid crystal cell with good adhesion durability and has the characteristic that a liquid crystal display device obtained therefrom is less liable to cause light leakage even under the environment of high temperature and high humidity and which makes it possible remove the polarizing plate. The pressure-sensitive adhesive for polarizing plates is prepared by irradiating a pressure-sensitive adhesive material comprising (A) an acrylic base polymer having a weight average molecular weight of 1,000,000 or more comprising a monomer having a hydroxyl group in a monomer composition ratio of 10 mass % or less, (B) an acrylic base polymer having a weight average molecular weight of 1,000,000 or more comprising a monomer having a carboxyl group in a monomer composition ratio of 10 mass % or less and (C) an active energy beam-curable compound with an active energy beam, wherein a mass ratio of the component (A) to the component (B) is 100:1 to 100:50, and a storage elastic modulus (G') at 23° C. is 0.3 MPa or more.

Methods are disclosed for synthesizing nanocomposite materials including ferromagnetic nanoparticles with polymer shells formed by controlled surface polymerization. The polymer shells prevent the nanoparticles from forming agglomerates and preserve the size dispersion of the nanoparticles. The nanocomposite particles can be further networked in suitable polymer hosts to tune mechanical, optical, and thermal properties of the final composite polymer system. An exemplary method includes forming a polymer shell on a nanoparticle surface by adding molecules of at least one monomer and optionally of at least one tethering agent to the nanoparticles, and then exposing to electromagnetic radiation at a wavelength selected to induce bonding between the nanoparticle and the molecules, to form a polymer shell bonded to the particle and optionally to a polymer host matrix. The nanocomposite materials can be used in various magneto-optic applications.

The present invention provides an acrylic resin composition containing a polycrystal of colloidal particles of silicon oxide in an acrylic resin that is formed by curing an acrylic monomer liquid at room temperature and/or an acrylic oligomer liquid at room temperature, wherein a mean distance between the colloidal particles in the polycrystal is 140 to 330 nm. The size of the single crystal that constitutes the polycrystal can be controlled by adjusting the content of silicon oxide and/or the additive amount of impurities. An architectural material, a fashion accessory, and an optical material are provided that are formed by using the acrylic resin composition.

Provided are methods of depositing polymer solutions on substrates to form various optical elements. A polymer solution may include about 0.1%-30% by weight of a specific polymer having rigid rod-like molecules. The molecules may include various cores, spacers, and sides groups to ensure their solubility, viscosity, and cross-linking ability. The deposition techniques may include slot die, spray, molding, roll coating, and so forth. Pre-deposition techniques may be used to improve wettability and adhesion of substrates. Post-deposition techniques may include ultraviolet cross-linking, specific drying techniques, evaporation of solvent, treating with salt solutions, and shaping. The disclosed polymers and deposition processes may yield optical elements with high refractive index values, such as greater than 1.6. These optical elements may be used as +A plates, −C plates, or biaxial polymers and used as retarders in LCD active panels or as light collimators and light guides.

A resin composition for forming an optical waveguide brings together excellent bending resistance, a low refractive index, and low tackiness suitable for a roll-to-roll (R-to-R) process as a material for forming an optical waveguide, in particular, a material for forming a clad layer. The resin composition for forming an optical waveguide to be used in formation of an optical waveguide includes a polyvinyl acetal compound having a structural unit represented by the following general formula (1) as a main component: in the formula (1), R represents an alkyl group having 1 to 3 carbon atoms, and k, m, and n represent ratios of respective repeating units in a main chain and each represent an integer of 1 or more.