A taper equation and associated tables are presented for red alder (Alnus rubra Bong.) trees grown in plantations. The data were gathered from variable-density experimental plantations throughout the Pacific Northwest. Diameter inside bark along the stem was fitted to a variable exponent model form by using generalized nonlinear least squares and a first-order continuous autoregressive process. A number of parameterizations of the exponent were examined in a preliminary analysis, and the most appropriate form was determined. This was achieved by examining alternative models across geographic locations and silvicultural treatments on the basis of their ability to behave well outside the range of the modeling data by using an independent evaluation data set from across the region and a model validation procedure. Incorporating three easily measured tree variables--diameter at breast height, total tree height, and crown ratio--provided the best fit among location and treatment. This taper equation can be used to estimate diameter inside bark anywhere along the stem, inside bark volume of the entire stem to any top height diameter, and merchantable height and volume between any two points along the stem (i.e., individual log volumes). The flexibility of the model allows for accurate volume predictions across a range of operational stand conditions and management activities and is therefore an improvement over previously published red alder volume and taper equations.

Soil disturbance is a visually apparent result of using heavy equipment to harvest trees. Subsequent consequences for growth of remaining trees, however, are variable and seldom quantified. We measured tree growth 7 and 11 years after thinning of trees in four stands of coast Douglas-fir (Pseudotsuga menziesii var. menziesii (Mirb. Franco)) where soil disturbance was limited by using planned skid trails, usually on dry soils. The three younger stands had responded to nitrogen fertilizer in the 4 years before thinning, but only one stand showed continued response in the subsequent 7- or 11-year period after thinning. The most consistent pattern observed was greater growth of residual trees located next to skid trails. The older stand also showed greater growth in trees located next to skid trails, whereas tillage of skid trails failed to benefit growth of nearby residual trees for the first 7 years after tillage. We conclude that traffic that compacted soil only on one side of residual trees did not reduce growth of nearby trees.

The effects of mechanical disturbance from traditional ground-based logging and site preparation on volcanic ash soil and associated tree growth were investigated by using two study approaches in a retrospective study. This research was conducted on volcanic ash soils within previously harvested units in the Blue Mountains of northeast Oregon and southwest Washington. We assessed soil and tree attributes and their association with higher and lower levels of soil disturbance. The two approaches were independent efforts that yielded very different results.

This paper describes a growth model for young plantations of Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) growing in the Pacific Northwest. The overall model has three major components. The first is a yield model for diameter and height distributions describing stands prior to pruning or precommercial thinning. The second component is an annual per-acre net increment model adapted from a recent model for Douglas-fir plantations in New Zealand; thinning and pruning are features of the model. The third component is growth equations for cohorts of individual trees; the results from this component are adjusted to match those from the second component. Fitting data are from Stand Management Cooperative experiments, with top heights generally below 75 ft. An intended use of the model is the evaluation of pruning regimes, in conjunction with the ORGANON model for growth at older ages, and TREEVAL model for clear-wood recovery and economic evaluation.

Old growth revisited: integrating social, economic, and ecological perspectives.

Late-successional and old-growth (LSOG) monitoring characterizes the status and trends of older forests to answer such questions as: How much older forest is there? Where is it? How much has changed and from what causes? Is the Northwest Forest Plan (the Plan) maintaining or restoring older forest ecosystems to desired conditions on federal lands in the Plan area? This assessment is the second in a continuous monitoring cycle. We initially reported on LSOG status and trends from 1994 to 2003 in the "10-year report." This document, the mid-cycle "15-year report," updates the assessment to 2006 in Washington and Oregon and to 2007 in California. The next major assessment will be the 20-year report.

This report documents the results from the first “5-year” round of understory responses to the Tongass-Wide Young-Growth Studies (TWYGS) treatments, especially in relation to their effects on food resources for black-tailed deer (Odocoileus hemionus sitkensis). Responses of understory vegetation to precommercial silviculture experiments after their first 4 to 8 years posttreatment were analyzed with the Forage Resource Evaluation System for Habitat (FRESH)-Deer model. The studies were conducted in western hemlock (Tsuga heterophylla)-Sitka spruce (Picea sitchensis) young-growth forests in southeast Alaska. All four TWYGS experiments were studied: (I) planting of red alder (Alnus rubra) within 1- to 5-year-old stands; (II) precommercial thinning at narrow and wide spacings (549 and 331 trees per hectare, respectively) in 15- to 25-year-old stands; (III) precommercial thinning at medium spacing (420 trees per hectare) with and without pruning in 25- to 35-yearold stands; and (IV) precommercial thinning at wide spacing (203 trees per hectare) with and without slash treatment versus thinning by girdling in >35-year-old stands. All experiments also included untreated control stands of identical age. FRESHDeer was used to evaluate the implications for deer habitat in terms of forage resources (species-specific biomass, digestible protein, and digestible dry matter) relative to deer metabolic requirements in summer (at two levels of requirements—maintenance only vs. lactation) and in winter (at six levels of snow depth).

Stem decays of living trees, known also as heart rots, are essential elements of wildlife habitat, especially for cavity-nesting birds and mammals. Stem decays are common features of old-growth forests of coastal Alaska, but are generally absent in young, managed forests. We offer several strategies for maintaining or restoring fungal stem decay in these managed forests that can be used to enhance specific types of wildlife habitat.

Six of nine nonnative boreal conifers in three genera (Abies, Larix, and Pinus) regenerated in 11 to 31 years after they were introduced to mainland Alaska. Lodgepole pine (Pinus contorta var. latifolia Engel.) and the Siberian larches (Larix sibirica Ledeb. and L. sukaczewii N. Dyl.) were the most widely introduced species and will likely be the first nonnative conifers to naturalize. Siberian larch grew up to six times more stem volume than white spruce in the first 40 years on upland sites, but was susceptible to the larch sawfly and a blue stain pathogen carried by bark beetles. On productive sites, lodgepole pine appeared to grow more stem wood than white spruce for about 35 years after planting. Snowshoe hares and moose were the most serious pests of the nonnative conifers. Balsam fir (Abies balsamea (L.) Mill.) was the only species to regenerate in an established moss understory. Growth and age relationships were negative for all adequately sampled nonnative conifers and positive for native white spruce (Picea glauca (Moench) Voss). Data were insufficient to assess niche availability for commercial-use of productive nonnative conifers in mixed stands in Alaska. Survey results indicate that introduction and naturalization of noninvasive tree species may improve the diversity, stability, and productivity of managed forest ecosystems.

Being brought up in Newcastle holds many different memories for all of us and being a Geordie is something to be proud of.

The INTERNATIONAL FEDERATION OF THE PHONOGRAPHIC INDUSTRY's (IFPI) "Global Music Report 2020" states the global recorded music industry generated $20.2 billion in wholesale … more

Statement Highlights: In a new scientific statement, the American Heart Association supports the creation of specialized multidisciplinary clinical programs that combine cardiovascular medicine and genetics expertise. These specialized programs would use genetic information to better treat patients with inherited heart conditions, as well as assess family members without current heart problems and take steps to reduce their risk.

We are living in unprecedented times. The global pandemic has had a major impact on our lives and our economy. In addition to the vast personal losses across the country and across the world, so many businesses have been negatively impacted. According to CNBC, retail sales fell by 8.7% in March of 2020, the biggest...

I sometimes get asked by regular people in the actual real world what it is that I do for a living, and here's my 15 second answer:

We built a sort of Wikipedia website for computer programmers to post questions and answers. It's called Stack Overflow.

As of last month,

Try these 10 actionable steps for streamlined, cost-effective marketing during the lockdown. Shed costs and embrace innovation to drive leads and conversions.

At no other time in the history of the internet has it been easier to design your own logo than it is right now. You could say that the world of online logo design makers is in a perfect position to...

Consider an infinite planar graph with uniform polynomial growth of degree d > 2. Many examples of such graphs exhibit similar geometric and spectral properties, and it has been conjectured that this is necessary. We present a family of counterexamples. In particular, we show that for every rational d > 2, there is a planar graph with uniform polynomial growth of degree d on which the random walk is transient, disproving a conjecture of Benjamini (2011).

By a well-known theorem of Benjamini and Schramm, such a graph cannot be a unimodular random graph. We also give examples of unimodular random planar graphs of uniform polynomial growth with unexpected properties. For instance, graphs of (almost sure) uniform polynomial growth of every rational degree d > 2 for which the speed exponent of the walk is larger than 1/d, and in which the complements of all balls are connected. This resolves negatively two questions of Benjamini and Papasoglou (2011).

Monadic second order logic can be used to express many classical notions of sets of vertices of a graph as for instance: dominating sets, induced matchings, perfect codes, independent sets or irredundant sets. Bounds on the number of sets of any such family of sets are interesting from a combinatorial point of view and have algorithmic applications. Many such bounds on different families of sets over different classes of graphs are already provided in the literature. In particular, Rote recently showed that the number of minimal dominating sets in trees of order $n$ is at most $95^{frac{n}{13}}$ and that this bound is asymptotically sharp up to a multiplicative constant. We build on his work to show that what he did for minimal dominating sets can be done for any family of sets definable by a monadic second order formula.

We first show that, for any monadic second order formula over graphs that characterizes a given kind of subset of its vertices, the maximal number of such sets in a tree can be expressed as the extit{growth rate of a bilinear system}. This mostly relies on well known links between monadic second order logic over trees and tree automata and basic tree automata manipulations. Then we show that this "growth rate" of a bilinear system can be approximated from above.We then use our implementation of this result to provide bounds on the number of independent dominating sets, total perfect dominating sets, induced matchings, maximal induced matchings, minimal perfect dominating sets, perfect codes and maximal irredundant sets on trees. We also solve a question from D. Y. Kang et al. regarding $r$-matchings and improve a bound from G'orska and Skupie'n on the number of maximal matchings on trees. Remark that this approach is easily generalizable to graphs of bounded tree width or clique width (or any similar class of graphs where tree automata are meaningful).

By Energy.Gov Annual reports analyzing the wind energy industry released today by the Energy Department show continued rapid growth in wind power installations in 2015, demonstrating market resilience and underscoring the vitality of the U.S. wind energy market on a … Continue reading →

Disclosed herein are methods and reagents for determining the responsiveness of cancer to an epidermal growth factor receptor (EGFR) targeting treatment. The detection of these mutations will allow for the administration of gefitinib, erlotinib and other tyrosine kinase inhibitors to those patients most likely to respond to the drug.

A region growing algorithm for controlling leakage is presented including a processor configured to select a starting point for segmentation of data, initiate a propagation process by designating adjacent voxels around the starting point, determine whether any new voxels are segmented, count and analyze the segmented new voxels to determine leakage levels, and identify and record segmented new voxels from a previous iteration when the leakage levels exceed a predetermined threshold. The processor is further configured to perform labeling of the segmented new voxels of the previous iteration, select the segmented new voxels from the previous iteration when the leakage levels fall below the predetermined threshold, and create a voxel list based on acceptable segmented voxels found in the previous iteration.

A method for inhibiting the crystal growth rate of an amide compound present in a molten polyolefin-based resin and a method for producing a polyolefin-based resin molded article are provided. A phenol compound is incorporated into an amide compound-containing polyolefin-based resin such that a weight ratio, amide compound:phenol compound, is 60:40 to 10:90.

Described herein are methods and compositions for enhancing pathogen immunity in plants and improving plant growth.

Suspension concentrate compositions are disclosed for delivering S-(+)-Abscisic acid either alone or in combination with a second plant growth regulator to crop seed prior to planting as well as for foliar, soil drench, in-furrow and sprench (foliar spray and soil drench) applications are disclosed. The compositions, when properly combined in an aqueous carrier and processed through wet milling to achieve the desired particle size, will result in stable compositions that are desirable for treating crop seeds.

The present invention relates to methods and compositions for supplementing the soil/diet of plants in order to enhance plant growth, yield, hardening, as well as the recovery of plants which undergo transplantation. The present invention provides ribose and other pentose sugars and their derivatives, alone or in combination with other carbohydrates, electrolytes, minerals, enzymes, micronutrients, macronutrients, or other ingredients to enhance plant growth, yield, hardening, and aid in the recovery during and following transplantation.

The present disclosure relates to methods of facilitating bone growth. The method may include positioning a device around at least a portion of a bone exhibiting a defect, the device capable of retaining bone segments and micro-structured particles. The method may also include applying micro-structure particles within the device to the defect, wherein each of the micro-structure particles include at least one pore therein. In addition, the method may include aligning at least a portion of the micro-structure particles and applying a polymer to the particles and solidifying the polymer.

A heating electrode assembly for a crystal growth furnace includes: a heat insulation board unit that is disposed between a furnace wall and a heater, that includes a first surface facing the furnace wall and a second surface facing the heater, and that is formed with a hole extending through the first surface and the second surface; an electrode unit that includes an electricity input portion mounted to the furnace wall, a post portion disposed in the hole, and an abutment flange connecting the post portion and the heater; and an electrical insulating unit including a tubular sleeve that is disposed in the hole and that surrounds the post portion, and a pad that is clamped between the abutment flange and the second surface.

The present invention relates to novel antibodies, particularly antibodies directed against deletion mutants of epidermal growth factor receptor and particularly to the type III deletion mutant, EGFRvIII. The invention also relates to human monoclonal antibodies directed against deletion mutants of epidermal growth factor receptor and particularly to EGFRvIII. Diagnostic and therapeutic formulations of such antibodies, and immunoconjugates thereof, are also provided.

The present invention relates to compositions and methods for inhibiting the activity of an enzyme, for example, Protein Kinase B, p70S6K and/or Abl using the catalytic subunit of Protein Kinase A (PKAc), or at least one PKAc fragment or variant PKAc fragment thereof. In this regard, methods for preventing or treating cancer or a neurodegenerative disease or disorder are also provided.

The invention relates to human medicine and to the use of epidermal growth factor (EGF) for preparing a pharmaceutical composition which is administered by infiltration into the periphery of nerve ganglia and/or trunks for the morphofunctional restoration of peripheral nerves in painful sensory-motor neuropathy as well as manifestations of ischemic neuritis. The invention also includes a composition containing EGF which can be formulated together with anesthetics or analgesics or encapsulated in microspheres and to the use thereof for the morphofunctional restoration of peripheral nerves in painful sensitive-motor-type diabetic neuropathy and the manifestations of ischemic neuritis.

The present invention is relevant to human medicine, and, in particular, to the use of Epidermal Growth Factor (EGF) in a pharmaceutical composition, said composition is administered through infiltration at the periphery of nerve trunks and/or ganglia, for the morphofunctional restoration of peripheral nerves in painful, sensory-motor neuropathy, as well as ischemic neuritis. It is also relevant to an EGF containing composition, where this molecule can be formulated together with anesthetic or analgesic drugs, or encapsulated in microspheres, and their use for the morphofunctional restoration of peripheral nerves in painful, sensory-motor neuropathy, as well as in ischemic neuritis.

A base at least one principal plane of which is a nitride is prepared for use in epitaxial growth. The base is placed on a susceptor in an epitaxial growth reactor and heated to a predetermined temperature (step A). The heating is started with inactive, nitrogen gas being supplied into the reactor. Then, active, NH3 gas is supplied. Then, a growth step (step B) of a first nitride semiconductor layer is started without an intervening step of thermally cleaning the principal nitride plane of the base. In step B, the first nitride semiconductor layer is epitaxially grown on a principal nitride plane of a base without supply of an Si source material. Then, a relatively thick, second nitride semiconductor layer is epitaxially grown on the first nitride semiconductor layer by supplying an n-type dopant source material (step C).

This technology is a method and apparatus for the semi-continuous measurement of the concentration of constituents of airborne particles which couples a laminar flow, water condensation particle collector to a microfluidic device for assay of particle chemical composition by electrophoresis. The technology has been used for the assay of sulfates, nitrates, chlorides, and organic acids contained in fine and submicrometer atmospheric particles. For these compounds the apparatus and method described is capable of one-minute time resolution at concentrations at the level of micrograms of analyte species per cubic meter of air. Extension to other analytes is possible.

A method for enhancing the production of aquatic organisms under cultivation, including the steps of exposing the aquatic organisms to a submerged illumination source inside water of a rearing unit; and maintaining illumination in the rearing unit for a rearing period.

The present invention is directed to recombinant thraustochytrids that grow on sucrose and cell cultures comprising the recombinant thraustochytrids as well as methods of producing cell cultures, biomasses, microbial oils, compositions, and biofuels using the recombinant thraustochytrids.

A composition comprising at least one nutrient element, wherein the at least one nutrient element possesses a relative energy-state value greater than the relative energy-state value of the at least one nutrient element in a preexisting state, the composition being effective, perhaps because of the greater energy-state value, to improve the ability of a soil, when combined with the composition, to support plant growth better than the soil, when not combined with the composition. Also a composition comprising at least one nutrient element, wherein the composition possesses an energy spectrum more positive than the energy spectrum of the composition in a preexisting state, the composition being effective, perhaps because of the more positive energy spectrum, to improve the ability of a soil, when combined with the composition, to support plant growth better than the soil, when not combined with the composition. Methods of making and using the same for improving soil, plants, plant growth, seeds, and/or plant products, including quality of plant products, are also disclosed, as well as improved soil, seeds, including quality of seeds, plants, and/or plant products, including quality of plant product.

The present media is to be used with a particulate base having particles of a first maximum diameter for growing plants. The media includes granules which are of biodegradable recycled material and have a diameter relative to the first maximum diameter to penetrate further into the particulate base with each watering. The granules include plant nutrients and are of a material which coagulates after watering and adheres to the particulates of the base. The diameter of the granules may be in the range of 1/16 to ⅛ of an inch.

The present invention provides apparatus and methods for growing fullerene nanotube forests, and forming nanotube films, threads and composite structures therefrom. In some embodiments, an interior-flow substrate includes a porous surface and one or more interior passages that provide reactant gas to an interior portion of a densely packed nanotube forest as it is growing. In some embodiments, a continuous-growth furnace is provided that includes an access port for removing nanotube forests without cooling the furnace substantially. In other embodiments, a nanotube film can be pulled from the nanotube forest without removing the forest from the furnace. A nanotube film loom is described. An apparatus for building layers of nanotube films on a continuous web is described.

Systems and methods for the formation of nanostructures, including carbon-based nanostructures, are generally described. In certain embodiments, substrate configurations and associated methods are described.

A method is provided for making smooth crystalline semiconductor thin-films and hole and electron transport films for solar cells and other electronic devices. Such semiconductor films have an average roughness of 3.4 nm thus allowing for effective deposition of additional semiconductor film layers such as perovskites for tandem solar cell structures which require extremely smooth surfaces for high quality device fabrication.

A general purpose plant growth medium and planting methods incorporating shredded coastal redwood bark for use in planting. In some embodiments the shredded coastal redwood bark fibers vary in length from about 0.125-14 inches and comprise about 10-80 % of the plant growth medium volume. In some embodiments the plant growth medium is compacted to an approximate unhydrated density of about 200-400 pounds per cubic yard.

A system for growing plants without soil uses removable V-shaped baskets to support plants in a tiered, self-contained unit. Nutrient enriched water is sprayed on the plant roots. The roots are held by perforations in the elongated V-shaped basket and a plant blanket. The unit is multilevel and can be set over an aquarium. The growing shelf can have a worm bag in order to add natural nutrients. Baskets can be comprised of a pair of identical halves that can be readily mutually coupled. Coupling mechanisms can include those that snap together and those providing for a pivoting coupling.

Certain novel formulations of plant growth media additives that act in such a manner as to permit proper amounts of moisture to contact root systems in order to reduce hydrophobicity within said media. The inventive formulation comprising multi-branched surfactant compounds with both hydrophobic and hydrophilic constituents within each branch attached to a polyfunctional base compound permit effective moisture penetration through plant growth media for sustained seedling and plant growth therein. Such multi-branched wetting agents provide sustained moisture penetration over a sustained period of time, since the individual branches of such compounds may become dissociated from its base polyfunctional compound. Since such branches include both hydrophobic and hydrophilic constituents themselves, and thus act as wetting agents, even after degradation of the initial surfactant compound, repeated wetting and moisture penetration, at least, are permitted. Methods of treating plant growth media with such compounds and formulations thereof are also contemplated within this invention.

A system for culturing photosynthesizing microorganisms includes a source of a gaseous fluid a mixer that creates micron bubbles within an aqueous medium using the gaseous fluid. The mixing chamber holds the aqueous medium including the micron bubbles before the micron bubbles and aqueous medium are mixed with a culture of photosynthesizing microorganism in a reaction chamber.

A method for cultivating algae can include providing a body of water in a substantially enclosed system. The enclosed system can have a length of channel and a cover. The method can optionally include circulating the body of water through the enclosed system under positive pressure conditions. The positive pressure should prevent ingress of any external atmosphere or material. Further, the method can include cultivating the algae in the body of water at conditions which promote growth. Likewise, a system for cultivating algae can include a channel with a cover, water in the channel, and a pump to introduce positive pressure into the system.

A cover for a plant-growing medium comprises a main cover portion, a peripheral base spaced from the main cover portion and defining an outer perimeter of the cover, and a peripheral wall extending from a first side of the main cover portion between the main cover portion and the peripheral base. One or more plant growth channels are defined by one or more tubes extending from the first side of the main cover portion. Each tube has a proximal end adjacent the main cover portion and a distal end relative to the proximal end, with a first aperture defined in the main cover portion at the proximal end of the tube and a second aperture defined at the distal end of the tube. The first aperture and the second aperture communicate through the tube to define each plant growth channel.

The present invention is directed to device and method for promoting plant growth. The device is a plant spacing member that has a body and a first end and a second end. The first end and second end have openings for receiving at least one plant limb therein to create a space between the limbs of the plant. An increased flow of air and light then flow through the created space to the interior of the plant to stimulate the growth of the plant. In addition, the increase flow of air and light dries the plant to reduce the accumulation of mold and mildew.

An apparatus is disclosed which may be used to grow plants in a chamber. In one embodiment, the chamber includes an artificial light source, a plurality of plant supports, a supporting structure configured to rotate the plant supports between two positions, the first position being closer to the artificial light source than the second, and a divider separating the chamber into a light region containing the artificial light source and one of the plant supports in the first position and a dark region containing the other plant support in the second position, wherein the divider is moveable between a first divider position in which the divider prevents movement of the plant supports and a second divider position in which the divider does not prevent movement of the plant supports. Methods of growing plants in a chamber on a moveable member are also disclosed.

Method and apparatus for growing plants in vertical stacks by providing vertically stacked, interconnected pairs of plant platforms and light trays carrying growth promoting light sources. Each light tray is suspended below the underside of the next above plant platform. The stack is vertically raised in succession whereby the plant platforms are suspended and vertically spaced from each other. Thereafter, plants are placed between suspended platforms under the light trays which are regulating during periods of plant growth and non-growth.

A plant growth container includes a tray, an inlet channel in the tray, a growth media retainer in the tray, one or more protrusions within the growth media retainer, an outlet channel connected to the growth media retainer, and a lid capable of being fixedly attached to the tray. The tray can be used in a hydroponic growth system for plants, where the system includes a container for growing plants. The container includes a tray, an inlet channel in the tray, a growth media retainer in the tray connected to the inlet channel, one or more protrusions in the growth media retainer, the protrusions capable of securing growth media from lateral movement, an outlet channel connected to the growth media retainer, and a lid. The system may include a reservoir for holding a liquid and a pump capable of pumping the liquid from the reservoir to the container.