Archives, Room Use Only - TK7871.72.D48 1949

Collecting back-scattered X-rays from vacuum windows using a pinhole X-ray camera provides an efficient and reliable method of measuring the beam shape and position of the white synchrotron beam. In this paper, measurements are presented that were conducted at ESRF beamline ID6 which uses an in-vacuum cryogenically cooled permanent-magnet undulator (CPMU18) and a traditional U32 undulator as its radiation sources, allowing tests to be performed at very high power density levels that were adjusted by changing the gap of the undulators. These measurements show that it is possible to record beam shape and beam position using a simple geometry without having to place any further items in the beam path. With this simple test setup it was possible to record the beam position with a root-mean-square noise figure of 150 nm.

The design and first results of a large-solid-angle X-ray emission spectrometer that is optimized for energies between 1.5 keV and 5.5 keV are presented. The spectrometer is based on an array of 11 cylindrically bent Johansson crystal analyzers arranged in a non-dispersive Rowland circle geometry. The smallest achievable energy bandwidth is smaller than the core hole lifetime broadening of the absorption edges in this energy range. Energy scanning is achieved using an innovative design, maintaining the Rowland circle conditions for all crystals with only four motor motions. The entire spectrometer is encased in a high-vacuum chamber that allocates a liquid helium cryostat and provides sufficient space for in situ cells and operando catalysis reactors.

A scanning soft X-ray spectromicroscope was recently developed based mainly on the photon-in/photon-out measurement scheme for the investigation of local electronic structures on the surfaces and interfaces of advanced materials under conditions ranging from low vacuum to helium atmosphere. The apparatus was installed at the soft X-ray beamline (BL17SU) at SPring-8. The characteristic features of the apparatus are described in detail. The feasibility of this spectromicroscope was demonstrated using soft X-ray undulator radiation. Here, based on these results, element-specific two-dimensional mapping and micro-XAFS (X-ray absorption fine structure) measurements are reported, as well as the observation of magnetic domain structures from using a reference sample of permalloy micro-dot patterns fabricated on a silicon substrate, with modest spatial resolution (e.g. ∼500 nm). Then, the X-ray radiation dose for Nafion® near the fluorine K-edge is discussed as a typical example of material that is not radiation hardened against a focused X-ray beam, for near future experiments.

Rosie the robot maid from the Jetsons isn't far behind.

The era of 900-watt-and-higher vacuum cleaners comes to an end in the European Union due to new efficiency standards.

Can a vacuum suck up China's smog? Daan Roosegaarde will test his new technology soon in Beijing's parks.

If an area rug under the table, to remember, the equivalent boundary extends parties, carpet should always be greater than the table itself. I remember the area to be selected to match the carpet, every room lifestyle. For example, sturdy fabrics and dark colors are ideal for high-traffic areas. On the other hand, the light tone carpet area cheering, to illuminate a room, deeper shades tend to add more warmth and comfort.

Disclosed are a vacuum glass panel and a manufacturing method of the same. The vacuum glass panel according to the present invention includes a first glass plate, a second glass plate facing the first glass plate with a vacuum space therebetween, an edge of the second glass plate being in contact with the first glass plate, and a plurality of spacers disposed between the first glass plate and the second glass plates to separate the first glass plate and the second glass plate from each other. The plurality of spacers are formed of a glass including alumina (Al2O3) particles and silica (SiO2) particles.

A centrifuge includes a vacuum pump machine configured of an auxiliary vacuum pump and an oil diffusion pump for exhausting gas inside a rotary chamber to outside, in which a rotor rotates at high speed. In the centrifuge, a thermistor for detecting a temperature of oil and an oil surface inside a boiler of the oil diffusion pump is provided inside the boiler, and power of a heater is adjusted with the temperature detected by the thermistor, so that a degree of vacuum inside the rotary chamber is stably reduced from atmospheric pressure to a high vacuum state. Besides, when the heater does not heat, a current is carried through the thermistor for self-heating, and it is determined from variation in a resistance value whether the oil exists or not at a position at which the thermistor 8 is placed.

A vacuum oven or vacuum furnace is disclosed having a heat distribution sleeve that conforms to the shape of an interior heating chamber. The heat distribution sleeve may be of generally annular shape, like a ring, and located in a substantially regularly spaced and offset relationship from a heating element located within walls adjacent the interior heating chamber. The heat distribution sleeve includes a thermal conductive material which absorbs and re-radiates heat emitted from the heating element, thereby providing more consistent and regular radiation fields for heating treating a work piece that is loaded on a work holding tray and, upon the vacuum oven being in an operational position, the work piece is located within the furnace chamber.

An electrode for a resistance analytical furnace has a crucible-engaging surface and an end spaced from the crucible-engaging surface having a plurality of grooves formed therein. A manifold mounted on the end of the electrode defines a dust recovery plenum and includes an outlet communicating with the plenum for coupling to a vacuum source to remove debris from the electrode. The improved electrode and electrode cleaning manifold positioned on the electrode provides a turbulent airflow for removal of dust and debris from an analytical furnace.

A vacuum apparatus and method for recovering poultry breast sub-tenders or other trim products from poultry or meat carcass shells, or for recovering other materials. The apparatus has a cover which can be lowered on to a base to form a vacuum chamber. One or more vacuum hoses extend from the apparatus for suctioning the product into the vacuum chamber. A product container is removably positioned in the vacuum chamber such that the product suctioned into the vacuum chamber will fall into the product container by gravity.

In order to solve the numerous problems with existing steam, vacuum, and hot water heating systems, presented are novel systems and methods of vapor vacuum heating having several improvements over the prior art, including: condensate return which can operate without steam traps; naturally-induced vacuum; improved vacuum pump operation for sustaining vacuum in such systems; liquid lift apparatus for use with such systems; and other improvements. All innovations presented herein make vapor vacuum heating more efficient and economical for industrial, commercial, and home applications. A field test conducted with these innovations show results of about 26-50% reduced energy usage, implying significant energy savings from the use of the present invention over current heating systems.

A valve, in particular a vacuum valve, in which, in order to close a passage opening, in particular of the valve, at least one closure member can be moved by a valve drive, starting from a maximum open position, in which the closure member opens the passage opening at least partially, first on a first partial path into an intermediate position, and the closure member can be moved, starting from the intermediate position, on at least one second partial path which is angled away from the first partial path into a closed position, in which the closure member closes the passage opening, the valve drive having at least two cylinder spaces which are loadable in each case with a pressure medium, at least one piston being mounted displaceably in each of the cylinder spaces, and the pistons being supported on one another by way of at least one prestressing element.

Systems, methods, and apparatus are provided to enable a vacuum tool to have a switchable plate, such that a common vacuum tool may be adapted with different plates. A switchable plate may form the entirety of the vacuum tool's material contacting surface or a switchable plate may form a portion of the material contacting surface. The vacuum tool is effective for picking and placing one or more manufacturing parts utilizing a vacuum force.

A vacuum-lifting device of variable configurations includes a first slat element, a second slat element, and four suction members. The first slat element is detachably fixed to the second slat element, and the first slat element intersects with the second slat element defining an intersection. A first slot is defined in the first slat element and a second slot is defined in the second slat element. Two of the four suction members are translatably secured in the first slot. The other two of the four suction members are translatably secured in the second slot.

A pick-and-place vacuum nozzle including a a nozzle body, a vacuum chamber within the nozzle body, a cavity formed in a lower surface of the nozzle body below the vacuum chamber, wherein the cavity is shaped to hold a head gimbal assembly, a back pressure relief hole passing through the nozzle body and connected to the vacuum chamber, the back pressure relief hole communicating with an exterior of the nozzle body, wherein a diameter of the back pressure relief hole is between 0.5 mm and 1 mm. The backpressure relief hole prevents light parts from sticking to the nozzle tip after vacuum is no longer applied.

A vacuum-lifting device includes a holding block and a nozzle. The holding block defines a holding hole and a threaded hole communicating with the holding hole. The nozzle includes a first section that is slidably received in the holding hole and a second section. The second section extends from the first section and has an outer diameter smaller than an outer diameter of the first section.

A system and method scrub a vapor. In embodiments, a vacuum truck scrubber system includes a liquid vat, a first carbon canister, a second carbon canister, and a third carbon canister. The first carbon canister and the second carbon canister each contain carbon. The liquid vat is connected to the first carbon canister. The first carbon canister is connected to the second carbon canister. A vapor having contaminants is fed to the liquid vat and is introduced from the liquid vat to the first carbon canister wherein a portion of the contaminants is removed from the vapor. The vapor is introduced from the first carbon canister to the second carbon canister wherein another portion of the contaminants is removed. The vacuum truck scrubber system also includes a monitoring system for reading and recording of sample measurements in the first carbon canister, the second carbon canister and the third carbon canister.

A highly reliable vacuum heat insulating material having excellent processability, usability and heat insulating performance and a heat insulating box using the vacuum heat insulating material are provided. A vacuum heat insulating material related to the present invention includes: a core material structured by a laminated structure of an organic fiber assembly formed by forming an organic fiber into a sheet shape and cutting an end face with a predetermined length, and having a core material opening portion formed by a through hole or a notch with cutting; a gas-barrier outer cover material containing the core material inside, having a sealing portion for sealing surrounding of the sheet-shaped organic fiber assembly and surrounding of the core material opening portion, and hermetically sealing an inside with almost vacuum status by sealing the sealing portion; and an outer cover material opening portion provided at the outer cover material under a status in which the sealing portion provided at the surrounding of the sheet-shaped organic fiber assembly and the surrounding of the core material opening portion is sealed, being a through hole or a notch which is smaller than the core material opening portion with a sealed amount, and a long fiber being equal to or longer than a length of the sheet is used for the organic fiber.

A seed meter is provided for use with a row crop planter or seed planter that includes a seed disk assembly that rotates within a meter housing cavity and that has a seed disk assembly cavity in which a vacuum pressure is applied for pulling seeds into seed pockets of a seed disk of the seed disc assembly. The vacuum pressure is applied to the seed disk assembly by pulling a vacuum airflow through a spindle that supports the seed disk assembly. A wiper seal is arranged in a fixed position within the seed disk assembly cavity and seals against the seed disk assembly as a support plate and seed disk of the seed disk assembly rotate over the wiper seal, so that the wiper seal creates a boundary between a vacuum zone and a non-vacuum zone inside of the seed disc assembly cavity.

A vacuum roller for a web handling system comprises a hollow, cylindrical, rotably driven drum and an end cap threadingly mounted onto the rear end of the drum. Together, the drum and the end cap define a plurality of individual, externally communicable vacuum paths. A spherical, metal movable element is internally disposed within each vacuum path and regulates the passage of air therethrough. A plurality of magnetic elements is fixedly mounted on a stationary annular holder. In use, each magnetic element selectively displaces each movable element when disposed in close proximity thereto to the extent necessary so as to permit the passage of air through its corresponding vacuum path. As such, the vacuum roller is provided with a predefined range of suction, or vacuum zone, about the outer surface of its rotating drum that directly corresponds to the angular arrangement of the plurality of stationary magnetic elements.

The present disclosure relates to a vacuum interrupter capable of easily installing a central arc shielding plate in alignment without biasing in a radial direction. The vacuum interrupter includes a protruding guide unit protruding from a stationary electrode seal cup in a perpendicular direction to guide the installation of the central arc shielding plate such that the central arc shielding plate can be aligned in a radial direction.

Disclosed are a power transmission device for a vacuum interrupter, and a vacuum breaker having the same. The device includes: a driving link coupled to an adjuster; a driven link coupled to a movable electrode of a vacuum interrupter; connection links configured to connect the driving link and the driven link with each other, and coupled to the driving link and the driven link such that an interval between the driving link and the driven link is varied; cams coupled to the connection links in a perpendicular direction; and cam guides having guide recesses for slidably coupling the cams, and configured to guide the interval between the driving link and the driven link to be changed.

The invention relates to a tap changer for the interruption-free switchover between winding taps of a tap-changing transformer. Furthermore, the present invention relates to a novel vacuum interrupter which is particularly suitable for such a tap changer. The tap changer according to the invention is based on the general concept of combining in each case one main contact (V1) and one mechanical switching means (U1), connected in series therewith, of a first load branch and an additional resistive contact (V3) of a second load branch in only a single vacuum interrupter (1) with a common housing (5). The vacuum interrupter (1) according to the invention is furthermore based on the general inventive concept of replacing the functionalities of two required vacuum interrupters in accordance with the prior art and an additional mechanical switching means with a single vacuum interrupter (1) according to the invention by virtue of combining the design of a vacuum interrupter (1) with a plurality of moveable contact systems (I, II, III), which are arranged in separate vacuum interrupter chambers (2, 3, 4) which are sealed with respect to one another.

In a vacuum circuit breaker corresponding to three-phase, which is configured by linearly arranging three pressure tanks respectively corresponding to one-phase, in which insulation gas is encapsulated, and a vacuum valve is installed, each pressure tank has a nearly longitudinal shape or a nearly square shape, viewed from a plane surface, and the vacuum valve is arranged in each of the pressure tanks in a state where a drive direction of the movable conductor is aligned with an upper lower direction, and the movable conductor is positioned lower than the vacuum valve, and keeps a sufficient insulation distance with respect to the movable-side connection conductor, and is neared to a position in one of diagonal directions or longitudinal directions of the pressure tank having a nearly square shape or nearly ellipsoidal shape, and moreover, the operation mechanism is arranged and configured at a position, which is lower than the vacuum valve.

An electrode assembly for a circuit breaker is provided. The electrode assembly includes a conductive assembly and a heat transfer assembly. The conductive assembly includes a stem portion and a contact portion. The heat transfer assembly includes a number of elongated bodies, a first heat transfer surface, and a second heat transfer surface. The first heat transfer surface is disposed on the conductive assembly. Each heat transfer assembly body includes a second heat transfer surface. Each heat transfer assembly body is coupled to the conductive assembly with the first heat transfer surface coupled to a number of second heat transfer surfaces.

A flexible shunt for a vacuum circuit breaker can have a reduced straight length and improved flexibility even with an increased thickness within a predetermined accommodation space of a main circuit part. The flexible shunt comprises a pair of conductive plates, each including a clamp connecting portion configured as a flat conductive member, the clamp connecting portion being connected the clamp, a terminal side connecting portion configured as a flat conductive member, the terminal side connecting portion being connected to the terminal side, and a flexible curved portion configured to connect the clamp connecting portion to the terminal side connecting portion, the flexible curved portion being formed to be projected outwardly.

An electrode assembly for a vacuum interrupter is configured such that supporting members can support most of a contact electrode plate and a supporting electrode plate in an axial direction with coil conductors interposed therebetween. Accordingly, an impact generated between electrode assemblies upon a closing operation of the vacuum interrupter may be evenly distributed onto the supporting members, which may result in preventing each of the electrode plates and the coil conductors from being deformed. Also, the supporting members are inserted into the electrode plates and the coil conductors, thereby effectively preventing a current from flowing via the supporting members. In addition, the supporting member may be wide and large so as to simplify an assembly operation and reduce an assembly time.

An apparatus, particularly a chuck for retaining a thin part for micro-machining processing, is disclosed. The chuck is formed of a plate-shaped body having a first surface and a second surface opposite the first surface. The plate-shaped body includes a light-transmissive material, and at least one of the first surface or the second surface is a roughened surface. The chuck can be incorporated into a micro-machining system using a chuck support that allows light through to backlight a processed part for inspection.

A brush having a tubular housing and a comb rotationally mounted within a nozzle inlet of the housing, the comb having a plurality of channels there through with bristles secured to the comb between pairs of the channels, and a pivotal lever engaged with the comb for rotation between obverse and inverse positions.

A system for tire distillation including an upper chamber, a first conveyor configured to transport a tire through the upper chamber, a lower chamber located beneath the upper chamber, the lower chamber that includes an ultrasonic purge chamber configured to radiate the tire with ultrasonic radiation, a microwave radiation chamber configured to radiate the tire with microwave radiation, and a second conveyor configured to transport the tire from the ultrasonic purge chamber to the microwave radiation chamber. The system further includes a vacuum system configured to maintain an atmosphere in the ultrasonic purge chamber and the microwave radiation chamber under a vacuum wherein the tire is preheated during conveyance through the upper chamber from heat produced in the lower chamber.

A cryopump 10 includes: a first cryopanel including a radiation shield 18 having a shield opening 20 and a louver 23 arranged in the shield opening 20; a second cryopanel 24 surrounded by the first cryopanel; and a refrigerator 14 configured to cool the first cryopanel to a first cooling temperature and to cool the second cryopanel to a second cooling temperature lower than the first cooling temperature. A rough surface 42 is formed on the louver 23.

A vacuum insulated door structure comprises a first wall having a first edge, outer sidewalls that extend from the first edge to a perimetrical lip, a first inner surface and a first outer surface. A second wall has a second inner surface, a second outer surface and a second edge coupled to the perimetrical lip forming a cavity volume. The second wall includes inner sidewalls defining a second wall opening. The inner sidewalls extend to a back wall and define a second wall offset. A tubular member includes a first end coupled to a first conduit opening in the first wall and a second end coupled to a second conduit opening in the second wall offset. A barrier layer is disposed on the first and second walls and the tubular member. A cavity insulation material is disposed within the cavity volume which is hermetically sealed.

A method is provided for producing vacuum in a vacuum oil-stock distillation column and includes pumping a gas-vapor medium out of a column by an ejector into a condenser; feeding a gas mixture and a high-pressure gas into a second gas-gas ejector from which the vapor-gas mixture is fed into a second condenser. A condensate is directed from the condensers into a separator in which the condensate is separated into a water-containing condensate and a hydrocarbon-containing condensate. The hydrocarbon-containing condensate is removed while the water-containing condensate is fed into a steam generator in which heat is supplied to the water-containing condensate from a hot distillate removed from the vacuum column and steam is produced from the water-containing condensate, the steam is fed as a high-pressure gas into the gas-gas ejectors. A plant for carrying out the method is also provided.

A method of converting a conventional atmospheric frying device to a vacuum frying device is provided. The method includes positioning a hood on top of a conventional frying device to provide an enclosure for drawing a vacuum within the modified devices. In addition, the method can include strengthening the existing vat so that it is capable of withstanding the forces associated with vacuum frying.

A tool is disclosed for separating a semiconductor die from a tape to which the die is affixed during the wafer dicing process. The tool includes a pick-up arm for positioning a vacuum tip over a semiconductor die to be removed. The vacuum tip includes a non-uniform array of vacuum holes to grip the semiconductor wafer.

The instant disclosure relates to a customizable vacuum molding method for forming personalized luggage bags utilizing a customizable vacuum molding device having a main mold body (1) and a personalized pattern module (2) customized to suit a customer preference. The vacuum molding method comprising the steps of: 1) placing the personalized pattern module on a molding surface of the main mold body at a predetermined location; 2) placing a plastic luggage bag substrate onto the molding surface of the vacuum molding device and soften the substrate by heating; and 3) generating negative pressure in the vacuum molding device and stretching the plastic substrate onto the personalized pattern module on the molding surface of the main mold body while cooling the plastic substrate to form a personalized pattern. The instantly disclosed vacuuforming method provides a simple yet cost effective solution for manufacturing luggage bags having personalized patterns of a customer's choice.

A control system according to the principles of the present disclosure includes a fuel system diagnostic module and a pump control module. The fuel system diagnostic module performs a diagnostic test on a fuel system when a vacuum pump is switched off to prevent flow through the vacuum pump and thereby seal a portion of the fuel system from an atmosphere. The vacuum pump includes a cam ring, a rotor that rotates within the cam ring, and vanes that slide into and out of slots in the rotor as the rotor rotates. The pump control module switches on the vacuum pump for a predetermined period to force the vanes out of the slots and into contact with the cam ring to seal the vacuum pump before switching off the vacuum pump for the fuel system diagnostic test.

Systems and methods for separating fluids from drill cuttings. Specifically, the invention relates to shakers that incorporate a vacuum system and methods of operating such systems to effect a high degree of fluid separation. The system and methods are effective across a variety of screen sizes, vacuum flows and vacuum designs.

A vacuum roll includes an inner rotor, an intermediate stator, and an outer shell roll. The inner rotor has open and closed portions and is adapted to rotate within the intermediate stator which is rotationally fixed and also has open and closed portions. The outer shell roll has open and closed portions and is adapted to move around the intermediate stator. Together the inner rotor and the intermediate stator define an internal rotary valve interface adapted to control fluid communication between the interior chamber and the outer shell.

Dryers and methods of using dryers are described herein. The dryer includes a housing, a drying chamber disposed within the housing, and a heating element. The dryer further includes an intake configured to supply intake air to the drying chamber. The dryer includes an exhaust configured to vent exhaust air out of the drying chamber. The dryer includes a pump coupled to the housing. The dryer further includes an energy recovery system coupled to the housing. The pump is configured to reduce the air pressure within the drying chamber. The energy recovery system includes a heat transfer fluid and is configured to use the heat transfer fluid to transfer thermal energy from the exhaust air to the drying chamber.

A vacuum mattress for an operation table has plural foam strips oriented longitudinally with respect to a patient, the foam strips being laterally spaced apart, wherein the gaps are free from granulate of the vacuum mattress at least in their upper parts and the plural foam strips are separated from the granulate by a gas-impermeable layer.

A vacuum filter backflushing system having an air recapturing adapter coupled to a vacuum motor's air exhaust port which recaptures a portion of exhaust air and introduces the air into a recaptured air passage. The recaptured air passage is coupled to an air flow director which is configured to direct air to an air filter. The air flow director is configured to selectively prevent air from flowing through the filters in a normal air flow direction and allow the air in the recaptured air passage to backflush the filter by dislodging particles from air filter media. The recaptured air passage can terminate after a last air filter, such that the recaptured air passage is pressurized, or the recaptured air passage can recouple back into the air exhaust port or the air recapturing adapter, such that the air is in constant motion in the recaptured air passage.

A system for flushing a vacuum toilet in an aircraft, with a bowl drain for removing toilet waste water from a bowl, a drain line, a bypass flow line for feeding-in air, a drainage valve and a waste water line. The bowl drain and the bypass flow line are connectable to the drain line, and the drainage valve on the input side is connectable to the drain line, and on the output side is connectable to a waste water line. In an implementation of the vacuum toilet as a vacuum urinal, the system may provide either water flushing or waterless flushing.

Air permeable core material is vacuum sealed in enveloping member. Further, core material is formed of at least two layers of heat insulating core materials having different heat conductivities. Further, at least two of the at least two layers of heat insulating core materials which form core material are formed of materials having change gradients in the heat conductivity changed in accordance with temperature, and the change gradients in the heat conductivity of the heat insulating core materials intersect with each other. Since two layers of heat insulating core materials having different heat conductivities are provided in a vacuum state, a heat insulating property becomes higher compared to a conventional configuration in which a single layer of the heat insulating core material formed of fiber material such as glass wool or rock wool is vacuum sealed and the high heat insulating property is shown in a wide temperature range.

A vacuum-assisted in-needle capillary adsorption trap (VA-INCAT) device for sampling and delivering materials to an analytical device is disclosed. A sorbent is multiwall carbon nanotube/polyaniline (PANI/MWCNT) nanocomposite and is coated within an interior space of the needle between the second end and the side aperture to entrap an analyte within a sample. The VA-INCAT device also includes a vacuum device configured to vacuum the vacuum flask to improve the extraction of the analytes vapors from the sample matrix to the sorbent bed.

An apparatus and related method of utilizing articulating vacuum plates to manipulate a film or polymeric sheet and form a three dimensional article is provided. The apparatus can be in the form of an articulating vacuum plate system which includes one or more plates or mold parts that are configured to support a sheet, constructed for example, from a polymeric film, in a two dimensional configuration or a three dimensional configuration in a first mode. The apparatus is constructed so that the plates and/or mold parts can articulate or move so as to reconfigure the sheet from a generally planar configuration into a second three dimensional configuration in a second mode for further forming, optionally while the plates and/or mold parts apply vacuum to the sheet while the plates and/or mold parts articulate, so that the plates and/or mold parts bend or otherwise manipulate the configuration and shape of the sheet.

Method and apparatus for lamination of substrates, e.g. rigid plastic layers, to manufacture laminated products. The methods include the sequential application of vacuum and mechanical force through a two-stroke process performed by a lamination apparatus having one or more force-producing stroke cylinders. Actuation of a cylinder to produce a first stroke creates a sealed chamber within the apparatus, enclosing a stack of substrates to be laminated. The sealed chamber may be evacuated of air by application of a vacuum. Subsequent actuation of a cylinder to produce a second stroke applies mechanical force to the sealed chamber, which compresses the substrates into a laminated product substantially free of air bubbles or voids.