I am working with innovus on a huge design. I found some cells are placed far away from both timing start points and timing end points. I suspect some other timing paths may be near-critical that results in this sub-optimal cell placement; or innovus has to place the cell far away due to congestion of placement or routing.

Is there a way to see why innovus places/moves the cell during place_opt_design or ccopt_design?

Also, is there a way to highlight all timing start points or timing end points that go through a cell? There may be thousands of timing paths through this cell. I tried using report_timing and timing debugger but it is very painful to click the highlight box and highlight the timing paths one by one.

Thank you for your help!

for debug I use suspend in my tcl script to debug，here is the code

after that the innovus command screen become 

how to quit the SUSPEND status？ thanks

Hi everyone. 

I'm very a new cadence user. I'm not good at using it and quite lost in finding a way to get the results. With the topic, I would like to ask you for some suggestions to improve my cadence skills.

I have some digital decision logic. Some are combinational logic, some are sequential logic that I would like to import or generate random input combination to the inputs of my decision logic to get the maximum, minimum, and average delay power dissipation and area when feeding the different input combination.

My logic has 8-bit, 16-bit, and 32-bit input. The imported data tends to be decimal numbers.

I would like to ask you:

- which tool(s) are the most appropriate to import and feed the different combination to my decision logic?

- which tool is the most appropriate to synthesis with different number of input? - I have used Genus Synthesis Solution so far. However with my skill right now I can only let Genus synthesize my Verilog code one setup at a time. I'm not sure if I there is anyway I can feed a lot of input at a time and get those results (min, max, average of delay, power dissipation and area)

- which language or scripts I should pick up to use and achieve these results?

-where can I find information to solve my problem? which information shall I look for?

Thank you so much for your time!!

Best Regards

I have a 2-dimensional input in my design - input [2:0] data_in [15:0]. After synthesis with genus, I got a netlist where the inputs are like data[15], data[14],...,data[0]. And furthermore it has definitions like input [2:0] data[15], .... So how can I define the pin locations of each of the bits for this input? Can I define data[15]'s inner bits like data[15][0]? Is it possible to define this with def files?

Hi! I've made some 1-point waveform "markers" that I want to overlay in my plots to aid visualization (with the added advantage, w.r.t. normal Viva markers, that they update location automatically upon refreshing simulation data).

For example, the plot below shows an spectrum along with two of these markers, which I create with the function "singlePointWave", and the Assembler output definitions also as shown below.

The problem is: as currently created and defined, Assembler is unable to plot these elements. I can send their expressions to the calculator and plotting works from there, BUT ONLY after first enabling the "Allow Any Units" in the target Viva subwindow.

Thus, I suspect Assembler is failing to plot my markers because they "lack" other information like axes units and so on. How could I add whatever is missing, so that these markers can plot automatically from Assembler?

Thanks in advance for any help!

Jorge.

P.S. I also don't know why, but nothing works without those "ymax()" in the output definitions--I suspect they are somehow converting the arguments to the right data type expected by singlePointWave(). Ideas how to fix that are also welcome! ^^

procedure( singlePointWave(xVal yVal)
    let( (xVect yVect wave)
        xVect = drCreateVec('double list(xVal));
        yVect = drCreateVec('double list(yVal));
        wave = drCreateWaveform(xVect yVect);
    );
);

I want to create sub tree of sub trees how can i do that?

I want to create another tree for the Sub parameter also.

I am attempting to use dbGetNeighbor() function inside the dynamic display HUD so that the distance to the next metal on that layer could be viewed. Think of another line in this dynamic table here... 

My SKILL code is essentially the following:

procedure(getNearestNeighborOnMetal(cv)
let((direction tmpBoundingBox)
direction = internal_function()
tmpBoundingBox = dbCreateRect(geGetEditCellView() "tmp" list(hiGetCommandPoint() hiGetCommandPoint()))
car(dbGetNeighbor(geGetEditCellView() tmpBoundingBox direction))
)
)

this returns the distance to the closest metal based on some tests.

Next, I try to register this function to work in the Dynamic Display / Info Balloon world by executing odcRegisterCustomFunc() for each and every object type (I know, absurd, but trying to debug)

In the dynamic display menu, I toggle the "Custom SKILL Function" check in layoutXL, then hit apply, then OK.

After this I find I am unable to view the changes reflected in any info balloons or in the drawing HUD (above) for this wire. I have tried replacing my function with the sample "customFunc" from the odcRegisterCustomFunc() documentation and was still unable to produce any new output.

Any help diagnosing the use of this feature would be very much appreciated

Hello,

I would like to create a button for my form that prompts the user to click on a cellview and draw a rectangle bounding box, exactly like the one used in the Area and Density Calculator. Can someone please help me with this?

Thanks!

Beto

Hi,

I want to define a procedure that with @key, and I also want to restrict the variable's datatype, I tried with folloing but I received error in CIW

procedure(tt(handler @key str1 str2 "ssS")
  printf("handler: %L " handler)
)

tt('test)

The error is like: *Error* tt: argument for keyword ?str1 should be a symbol (type template = "ssS") at line 11 of file

Thanks,

James

Hi everyone, 

Is there any method to generate "Sheet" column for a pin report like table below? The column "Name.Pin" & "Signal" can be generated easily, but I have no idea to generate the column of "Sheet Name".

The software using here are Allegro Design Entry HDL, OrCAD Capture and Allegro PCB Editor. Can these 3 software generate "Sheet Name" data?

Thank you. 

Good morning,
I dug up an old project from 2005 and I should open the schematic to check some things.
This is the schematic of a XILINX XC95108-pq160 CPLD which the XILINX ISE 6.1 software then translated and compiled, to generate a JEDEC file to burn CPLD.

My problem is that I can't open schematics with the versions of Orcad Schematic Entry that I have.
Can anyone help me understand which version of Orcad Schematic Entry I need to install to see these files?

I shared the files on:
drive.google.com/.../view

Thank you very much

hi

How can I tell the LEC tool to ignore a combination of Primary input bus in both Golden and revised.

For example in both Golden and revised there is 

input [3:0] data_in

I want LEC not to check the case that data_in[3:0] == 4'b1000

Have you ever encountered ERROR(SPMHNI-67) while importing logic? If yes, you might already know that you had to export libraries of the design and make sure that paths (devpath, padpath, and psmpath) include the location of exported files.  

Starting in SPB23.1, if you go to File > Import > Logic/Netlist and click on the Other tab, you will see an option, Reuse device files for existing components. 

After selecting this option, ERROR(SPMHNI-67) will no longer be there in the log file, because the tool will automatically extract device files and seamlessly use them for newly imported data. In other words, SPB_23.1 lets you reuse the device / component definitions already in the design without first having to dump libraries manually. An excellent improvement, don’t you think?  

Starting from SPB23.1, a new option, Allow DRCs to surrounding metal, has been added in the Etch-Back form to allow DRCs to the surrounding objects. form to allow DRCs to the surrounding objects.

The Allow DRCs to surrounding metal option lets you see and adjust objects instead of the current behavior, which sacrifices the width of the mask for the trace.

• When this option is turned off, it maintains the EB mask to another object clearance.
• When this option is enabled, it keeps the EB mask to the EM trace edge clearance and shows a DRC if the EB mask to another object spacing is out of rule.

Starting SPB 23.1, a new pin property, WIREBOND_PROFILE_NAME is introduced. This property can be used to define a wirebond profile to a die pin. When adding a wirebond, the pin will use the profile defined in the WIREBOND_PROFILE_NAME property associated to the die pin.

Assign the WIREBOND_PROFILE_NAME property to the die pin using Edit > Properties and set the desired wirebond profile name in the Value field.

The following image displays the WIREBOND_PROFILE_NAME property assigned to the pin and wire profile of the Wire Bond for that pin.

Have you ever thought of a handy utility to specify all necessary transmission line parameters to decide upon the stackup?   

Starting SPB 23.1, a handy feature Transmission Line Calculator, is built into Allegro X Advanced Package Designer (Allegro X APD). This feature will require either an SiP Layout license or can be accessed through SiP Layout Bundle. 

From the Analyze dropdown menu in the 23.1 Allegro X APD toolbar, you can choose Transmission Line Calculator. 

You can use this calculator to help decide constraints and stackup for laminate-based PCB or Packages. You can calculate the correct stackup material and width/spacing to meet any requirements that may be later entered in a constraint. This is truly a calculated number and not a true field solver. 

The different types of calculations that the Transmission Line Calculator can provide are Microstrip, Embedded microstrip, Stripline, CPW (Coplanar), FGCPW (frequency-dependent Coplanar), Asymmetric stripline, Coupled microstrip (Differential Pair), Coupled stripline (Differential Pair), and Dual striplines. 

This feature is important for customers relying on fabricators/spreadsheets to provide this information or need to test a quick spacing/width as per the impedance value. 

Let us know your comments on this new feature in 23.1 Allegro X APD. 

Starting SPB 23.1, Allegro X APD lets you import/export the symbol and component properties by using Die Text-In/Out wizards. 

Exporting the symbol 

You can export the symbol by using File > Export > Die Text-Out Wizard. 

In the Die Text-Out Wizard window, you can see the newly added options, that is, Component Properties and Symbol Properties. 

This entire information including the properties will be saved in a text file. 

Importing the symbol 

You can import the same text file in Allegro X APD by using Die Text-In Wizard. 

Choose the text file you want to import. 

Symbol properties added in the text file will be visible in the Die Text-In Wizard window. 

In a package design, designers often need to perform degassing. This is typically done at the end of the design process before sending the design to the manufacturer.

Degassing is a process where you perforate power planes, voltage planes, and filled shapes in your design. Degassing holes let the gas escape from beneath the metal during manufacturing of the substrate. The perforations or holes for degassing are generally small, having a specified size and shape, and are spaced regularly across the surface of the plane. If the degassing process is not done, it may result in the formation of gas bubbles under the metal, which may cause the surface of the metal to become uneven. After you degas the design, it is recommended to perform electrical verification.

Allegro X APD has degassing features that allow users to automate the process and place holes in the entire shape.

In today’s topic, we will talk about how to avoid adding  degassing holes on a particular shape.

Sometimes, a designer may need to avoid adding degassing holes to a particular shape on a layer. All other shapes on the layer can have degassing holes but not this shape. Using the Layer Based Degassing Parameters option, the designer can set the degassing parameters for all shapes on the layer. Now, the designer would like to defer adding degassing holes for this particular shape.

You may wonder if there is an easy way to achieve this. We will now see how this can be done with the tool.

Once the degassing parameters are set, performing Display > Element on any of the shapes on that layer will show the degassing parameters set.

You can apply the Degas_Not_Allowed property to a shape to specify that degassing should not be performed on this shape, even if the degassing requirements are met. Select the shape and add the property as shown below.

Switch to Shape Edit application mode (Setup > Application mode > Shape Edit) and window-select all shapes on the layer. Then, right-click and select Deferred Degassing > All Off.

Now, all shapes on the layer will have degassing holes except for the shape which has the Degas_Not_Allowed property attached to it.

By default, a dielectric must separate each pair of conductor layers in the cross-section of a design. In rare cases, this does not represent the real, manufactured substrate.

If your design requires you to have conductor layers that are not separated by a dielectric (such as, for half-etch designs), there is a variable that needs to be set in Allegro X APD. You must set this by enabling the variable icp_allow_adjacent_conductors. This entry, and its location in the User Preferences Editor, are shown in the following image.

The Objects on adjacent conductor layers do not electrically connect together, automatically. A via must be used to establish the inter-layer connections.

When enabling this option, it is recommended to exercise caution because excluding dielectric layers from your cross-section can lead to inaccurate calculations, including the calculations for signal integrity and via heights. It is important that your cross-section accurately reflect the finished product to ensure the most accurate results possible. Any dielectric layers present in the manufactured part need to be in the cross-section for accurate extraction, 3D viewing, and so on.

Let us know your comments on the various designs that would require adjacent conductor layers.

Hello, SKILL experts. 

I'm studying SKILL language to build some useful function in APD+.

Now, I want to execute 'Import Sub-drawing' function in new form.

But I cannot find how to do execute APD+ embedded function in a field of new form. 

Has anyone experienced this or idea to solve this problem? 

When the Arduino Mega2560 is added to the first serial port, the dynamic memory is 2000 bytes, and when the second serial serial is added, the dynamic memory is 4000 bytes. Now I need to add the third Serial serial port. The dynamic memory is 6000 bytes. Due to the many variables in the program itself, the dynamic memory is not enough. Please help me how to save the dynamic memory?

While doing the lvs it's showing an error in gnd connection, I am not being able to understand exactly what is the error and what do I need to do to remove this error?

Hi, all.

When I use vavlog to compile verilog rtl, it will recognize IO width mismatch problem as a fatal error.

How to turn the error into warning?

VCS can use -error=noIOPCWM to ingore the error.

Is vavlog has similar arguments?

Hi,

I need to design EPC8002 eGaN switch in cadence. Can someone provide me step by step guide on hoe to add EPC8002 into my cadence. I am working on BCD180.

Thank you 

Ihsan

Hi,

So I was trying to update the title block of a schematic that I have. The title block that was on there was out of date . I clicked on place --> title block and was able to find the title block that I need. I also have a .OLB file that contains that title block. Then I created a Netlist with the old BRD file as the input file (To keep it as is but modify changes) but when I do that I still do not see / cannot place the title block that I need. Under Place --> format symbols in Allegro , I do see a title block that is coming from the database (But it's the old one). I don't know what to do at this point and would appreciate any tips. I did make sure that the path to where the library is , is defined in the user preferences. 
I also tried copying the title block under the library folder in capture before creating my Netlist and that did not work either.

Thank you all.

I have a small board that is not readable even though the document is 11' x 17'. Is there a way I could expand/magnify the board along with the components on them to make them legible? 
I have created a new film and is displaying the bottom and top side of the board but the board is too small and the components are not legible. Perhaps there is a way to upscale it or expand it?
Please note I have other stuff in the document that I am not showing , notes and other things, and I am trying to make just the boards look bigger in some way.
I do have a PDF image of the same file where the board appears to be MUCH bigger and is fully legible and I am trying to match that.

Thank you all.

I want to use PSpice model (download from TI) in Virtuoso , but it can not work. Please help me to check the error message, Thanks

ADE-> Setup-> simulation files->Pspice  Files  /TPS628502-Q1_TRANS.LIB

Parse error before token ']' in expression '[[STEADY_STATE]*0.6]'. If '[[STEADY_STATE]*0.6]'  is a spice expression, quotes are required for the expression.

ERROR(SFE-46): An instance of 'TPS628502-Q1_TRANS'  can have at most 8 terminals (but has 9).

*****************************************************************************
.SUBCKT TPS628502-Q1_TRANS COMP_FSET EN FB GND PG SW SYNC_MODE VIN
+ PARAMS: STEADY_STATE=0
V_U9_V45 U9_N16725824 0 5
E_U9_ABM22 U9_N16725392 0 VALUE { V(FREQ)*1e-12 }
X_U9_U161 U9_N16849713 U9_N16846056 one_shot PARAMS: T=20

Hello

i did a sp-Analysis and now i want to extract the maximum value of the s11 trace and the corresponding frequency.

I already tried ymax() in the calculator but i am suspecting it only works on transient Signals.

Hello everyone,

I hope you're all doing well. I’ve set up two testbenches (TB1 and TB2) for my Design Under Test (DUT) using Cadence IC6.1.8-64b.500.21 tools, as shown in the attached figure. The DUT has multiple views available: schematic, Calibre, Maestro, and Symbol, and each testbench uses the same DUT in different scenarios. Currently, I have to manually switch between these views, but I would like to streamline this process.

My goal is to use a single config view that allows me to switch between the schematic and the extracted (Calibre) views. Ideally, I would like to have a configuration file where making changes once would update both testbenches (TB1 and TB2) automatically. In other words, when I modify one config, both testbenches should reflect this update for a single simulation run.

I would really appreciate it if you could guide me on the following:

1. How to create a config view for my DUT that can be used to easily switch between the schematic and extracted views, impacting both TB1 and TB2.
2. Where to specify view priorities or other settings to control which view is used during simulation.
3. Best practices for using a config file in this scenario, so that it ensures consistency across multiple testbenches.

Please refer to the attached figure to get a better understanding of the setup I’m using, where both TB1 and TB2 include the same DUT with multiple available views.

Thank you so much for your time and assistance!

Hello,

I am aware of command script .svcf file that saves signals and loads them in while opening Simvision.

I am wondering, if there is a way for saving signals while we are in an interactive session and loading them next time when we open Simvision interactively.

Any ideas on how to do this?

Thank you in advance.

Swetha. C

I'm currently work in coverage analysis. In my design certain register bits remain unused, which could potentially lower toggle coverage. Specifically, I'd like to know how to disable coverage for specific unused register bits within a 32-bit register. For instance, I want to deactivate coverage for bit 17 and bit 20 in a 32-bit register to optimize toggle coverage. Could you please provide guidance on how to accomplish this?

Hi all, I've trained a device model with the approach of an artificial neural network, and it shows well fit. 

May I know how to transfer the trained model to Verilog-A, so that, we can use this model to do circuit simulation?

And I've searched for some lectures that provide the Verilog-A code in the appendix, but I'm freshman in the field of Verilog-A, 

could anyone tell me each statement? such as

real hlayer-w[0:(NI*NNHL)-1   

Is there a way to set a thru via hole to thru via hole spacing constraint?

I need the hole to hole spacing, nit pad to pad spacing.

I can calculate the spacing using the via pad diameter, but this won't work for multiple via pad sizes.

Hi

I have fixed a SPACING RULE (SP1) for a CLASS_DIFF_PAIR whereas for via associated to the net (DP_VIA), the DISTANCE > 60mils respect to ANY other vias (PTH, BB, TEST vias)

Now my problem is that this rules should NOT be applied for GND VIAS (STICHING VIA) which must be placed at a distance < 40mils respect to DP_VIA

How to create an exemption to the SPACING RULE (SP1)?

Dear Community,

I have created a PCB layout with multiple high-speed nets, I want to check the SI like how signals are reflected and taken to each other.

I have the OrCAD X Professional, how to check the reflection and crosstalk using the OrCAD X Professional software version 24.1.

I want to create a topology flow to the PCB layout and perform the reflection and crosstalk.

Regards,

Rohit Rohan

Hai Community,

I have a PCB board which has multiple high speed nets and I want to perform the EMI and EMC checking.

Which Cadence tool should I use for checking the EMI and EMC coupling?

Regards,

Rohit Rohan

Dear Community,

In OrCAD X Profession, the workspace feature enables the users to store the libraries (Schematic Symbol, Footprint and PSpice Models) and Designs (Schematic and PCB layout) in the cloud workspace.

But storing these libraries and design are stored in servers in the USA, Europe, Asia and Japan Servers.

I don't want to store my designs in any of these servers instead I want to create the workspace in my local PC and store all my libraries and designs in the local workspace.

Is this possible, if possible then can anyone provide the steps/procedure or videos of how to do it?

Regards,

Rohit Rohan

Dear Community,

I have created a PCB board and let's say I have found some parts of the PCB board where there are impedance issues, then how to resolve that impedance issue using the OrCAD X Professional.

Regards,

Rohit Rohan

Here are the best ways to watch Pharrell Williams' Lego-inspired biopic 'Piece by Piece' — including the best Peacock streaming deals.

Red Cup Day at Starbucks is coming up soon. Here's how to get a free red reusable cup.

Watch 'I'm a Celebrity...Get Me Out of Here!' for free from anywhere in the world.

Live stream the 2024 ATP Finals for free from anywhere in the world.

Live stream Sinner vs. Fritz in the 2024 ATP Finals online for free from anywhere in the world.

Bypass geo-restrictions to watch MotoGP 2024 for free from anywhere in the world.

As generative AI evolves and accelerates industry, a community of AI enthusiasts is experimenting with ways to integrate the powerful technology into common productivity workflows.

Check here each week to keep up with the latest from John MacArthur's pulpit at Grace Community Church.

Check here each week to keep up with the latest from John MacArthur's pulpit at Grace Community Church.

Check here each week to keep up with the latest from John MacArthur's pulpit at Grace Community Church.

Check here each week to keep up with the latest from John MacArthur's pulpit at Grace Community Church.