The 2021 USHGC is scheduled to be published in early 2021.

Photovoltaic markets can be classified based on the end-use application of the technology. The most common PV projects are off-grid applications. Water pumping also represents an important application of PV, particularly in developing countries. The largest long-term market potential for... Read more

The post Photovoltaic End-Use Application Markets appeared first on EEP - Electrical Engineering Portal.

– Array Size: 10, 12-volt, 51-watt modules; Isc= 3.25 amps, Voc= 20.7 volts – Batteries: 800 amp-hours at 12 volts – Loads: 5 amps DC and 500-watt inverterwith 90% efficiency. The PV modules are mounted on the roof. Single-conductor cables... Read more

The post Calculation Example of Small Photovoltaic (PV) Residential Stand-Alone System appeared first on EEP - Electrical Engineering Portal.

In order to understand a photovoltaic (PV) installation and its components we must be familiar with the following terms: Standard Test Conditions (STC) PV modules PV string and Array The output of a PV module is not stable it depends... Read more

The post 3 Photovoltaic Installation Terms To Be Familiar With appeared first on EEP - Electrical Engineering Portal.

Twenty Bermudians recently completed the Solar Photovoltaic Certification Training Programme held in partnership with Connectech. A Government spokesperson said, “The Ministry of Home Affairs is pleased to advise the public that twenty Bermudians recently completed the Solar Photovoltaic or PV Certification Training Programme held in partnership with Connectech. “The student participants were selected from a […]

Improvements to device may eventually cut external power demands for buildings by 50%

The development of future recycling technologies must be informed by data about products and materials that will enter the waste stream, but such forecasts are subject to a high level of uncertainty. In this study, researchers have proposed a methodology for predicting emerging waste materials, applying it to silicon-based photovoltaic (PV) panels. The findings show that closed-loop recycling — when post-consumer waste is recycled to make new products — of PV panel materials could mitigate up to 0.2% of the annual environmental impact of Flanders1, Belgium, if suitable technology was developed.

Most modern societies depend on fossil fuels (oil, gas and coal) as sources of energy for development and growth. Switching to renewable energy sources, such as photovoltaic (PV) systems, is necessary for sustainable development in the future. A new study suggests that it is currently much more efficient to use fossil fuels to develop PV power plants than to combust the same amount of fossil fuels in conventional thermal power plants: thus the sooner PV systems are developed, the sooner society will reduce its reliance on fossil fuels.

Researchers have summarised the most effective ways that nanostructures can improve the efficiency and lower costs of photovoltaic (PV) solar cells in a recent analysis. Sculpting ultra-thin solar cell surfaces at the nano-scale has been found to effectively boost their efficiency.

Europe could struggle to meet the target set by the renewable energy sector of 25% of electricity produced by solar energy by 2040 because the supply of materials, including rare metals, needed to produce photovoltaics (PV) is unlikely to meet demand. Production rates need to be drastically improved, according to a new study.

Revolutionary production process allows a simple transfer of a common OPV preliminary product to real customised OPV products

The original OPV Solar Trees of the German Pavilion at the EXPO 2015 world exhibition in Milan have been reinstalled in Darmstadt.

OPVIUS GmbH and Taiyo Europe GmbH realize the world's first energy-efficient façade project in membrane architecture at a Merck KGaA building in Darmstadt.

As part of the renovation of a residential building belonging to the Frankfurter Wohnungsbaugesellschaft ABG, the first "in-plaster" photovoltaic system based on organic photovoltaic (OPV) technology in the world was implemented.

ARMOR has just reached an important milestone in the production of its flexible organic photovoltaic film, ASCA©.

The National Park Service and Arizona Public Service will be hosting a public event on Monday, May 18, at 11:00 a.m., to celebrate the installation of eighty-four photovoltaic solar panels at the Grand Canyon Visitor Center. https://www.nps.gov/grca/learn/news/news-2009-05-12-aps.htm

A photovoltaic cell, for example a thin-film photovoltaic cell, having a substrate glass made of aluminosilicate glass, has a glass composition which has SiO2 and Al2O3 as well as the alkali metal oxide Na2O and the alkaline earth oxides CaO, MgO, and BaO, and optionally further components. The glass composition includes 10 to 16 wt.-% Na2O, >0 to 1 to 10 wt.-% BaO, and the ratio of CaO:MgO is in the range of 0.5 to 1.7. The aluminosilicate glass used is crystallization stable because of the selected quotient of CaO/MgO and has a transformation temperature >580° C. and a processing temperature

1,4 fullerene deriatives useful for solar cells are provided, where their structures allow for straightforward functionalizations to tune their properties in terms of solubility and LUMO energy levels.

A system for controlling photovoltaic electricity production equipment having photovoltaic modules each equipped with a DC/DC microconverter connected to a DC bus, a DC bus manager, and an inverter for converting the direct current from the photovoltaic panels into alternative current intended for an electrical distribution network. Power is injected into the DC bus when the voltage of the DC bus is less than a minimum voltage until the minimum voltage is reached. Each of the microconverters injects a maximum power from the photovoltaic modules into the DC bus when the voltage of the DC bus is between a first voltage and a second voltage. The injecting of power from the photovoltaic modules into the DC bus is stopped when the voltage of the DC bus is less than a low threshold voltage or greater than a high threshold voltage.

An output converter includes a DCDC conversion section, a secondary side voltage/current monitoring section detecting a power from the DCDC conversion section, a maximum operation point control section determining what voltage is to be set by the DCDC conversion section so that the power detected by the secondary side voltage/current monitoring section is maximum, a DCDC short-circuit switch via which a current from a module bypasses the DCDC conversion section to outside, a primary side voltage/current monitoring section measuring the current from the module, a module short-circuit switch switching between a state where a secondary side cathode and a secondary side anode are short-circuited and a state where they are not short-circuited, the maximum operation point control section causing the DCDC short-circuit switch and the module short-circuit switch to switch.

Described herein are improved configurations for a wireless power transfer involving photovoltaic panels. Described are methods and designs that use electric energy from a photovoltaic module to energize at least one wireless energy source to produce an oscillating magnetic field for wireless energy transfer. The source may be configured and tuned to present an impedance to a photovoltaic module wherein said impedance enables substantial extraction of energy from said photovoltaic module.

Methods and apparatus for converting electromagnetic radiation, such as solar energy, into electric energy with increased efficiency when compared to conventional solar cells are provided. A photovoltaic (PV) device generally includes a window layer; an absorber layer disposed below the window layer such that electrons are generated when photons travel through the window layer and are absorbed by the absorber layer; and a plurality of contacts for external connection coupled to the absorber layer, such that all of the contacts for external connection are disposed below the absorber layer and do not block any of the photons from reaching the absorber layer through the window layer. Locating all the contacts on the back side of the PV device avoids solar shadows caused by front side contacts, typically found in conventional solar cells. Therefore, PV devices described herein with back side contacts may allow for increased efficiency when compared to conventional solar cells.

Disclosed is a photovoltaic device. The photovoltaic device includes: a substrate; a first electrode placed on the substrate; a second electrode which is placed opposite to the first electrode and which light is incident on; a first unit cell being placed between the first electrode and the second electrode, and including an intrinsic semiconductor layer including crystalline silicon grains making the surface of the intrinsic semiconductor layer toward the second electrode textured; and a second unit cell placed between the first unit cell and the second electrode.

This invention is directed to a flexible solar cell photovoltaic module with high light transmittance based on modified substrate, which belongs to the field of thin-film solar cell technology. The objective of the present invention to provide a technical solution for a transparent flexible solar cell module and its fabrication method. Technical features include using a stainless steel template to mold a modified polyimide PI substrate (the PI substrate). The PI substrate has light-passing through-holes, including draining holes and convergence holes, through and distributed on the PI substrate, a conductive film layer, and various stacked photoelectric conversion film layers. The creativeness of the present invention is obvious, such as reducing the short circuit and current leakage due to crystallization of the photoelectric layer interface caused by a subsequent process of laser etching the conductive film layer, reducing the composition on the surface of the solar cell, reducing steps of the fabrication process, and lowering the production cost. Further, the present invention significantly increases the conversion efficiency and load capacity of the solar cell and the quality-cost ratio. The transparent flexible solar cell photovoltaic module also has a broad range of applications.

A resin composition, a multi-layered film, a backsheet for photovoltaic modules, a method thereof, and a photovoltaic module are provided. The multi-layered film including a coating layer including a fluorine-based polymer has an excellent durability and weather resistance, and also exhibits high interfacial adhesive strength to a substrate since the multi-layered film is formed by coating a cured product of the resin composition including the fluorine-based polymer, an acrylic polymer including a thermosetting functional group, and a heat-curing agent on the substrate. In addition, drying can be performed at a low temperature during the manufacture of the multi-layered film so that the manufacturing costs can be decreased, productivity can be increased, and the deterioration of the product due to heat modification, heat shock, and the like, can be prevented. The multi-layered film can be effectively used as a backsheet for various photovoltaic modules.

Novel photoactive polymers, as well as related photovoltaic cells, articles, systems, and methods, are disclosed.

A PV panel uses an array of small silicon sphere diodes (10-300 microns in diameter) connected in parallel. The spheres are embedded in an uncured aluminum-containing layer, and the aluminum-containing layer is heated to anneal the aluminum-containing layer as well as p-dope the bottom surface of the spheres. A phosphorus-containing layer is deposited over the spheres to dope the top surface n-type, forming a pn junction. The phosphorus layer is then removed. A conductor is deposited to contact the top surface. Alternatively, the spheres are deposited with a p-type core and an n-type outer shell. After deposition, the top surface is etched to expose the core. A first conductor layer contacts the bottom surface, and a second conductor layer contacts the exposed core. A liquid lens material is deposited over the rounded top surface of the spheres and cured to provide conformal lenses designed to increase the PV panel efficiency.

A method for fabricating a photovoltaic device includes depositing a p-type layer at a first temperature and depositing an intrinsic layer while gradually increasing a deposition temperature to a final temperature. The intrinsic layer deposition is completed at the final temperature. An n-type layer is formed on the intrinsic layer.

A photovoltaic cell comprises a top subcell having a first band gap; a middle subcell comprising a substrate and having a second band gap, wherein the substrate comprises a first side and a second side opposite to the first side; and a bottom subcell having a third band gap, wherein the top subcell is grown on the first side of the substrate and the bottom subcell is grown on the second side of the substrate, wherein the first band gap is larger than the second band gap and the second band gap is larger than the third band gap.

A photovoltaic device including a substrate; a first electrode placed on the substrate; a second electrode which is placed opposite to the first electrode and which light is incident on; a first unit cell being placed between the first electrode and the second electrode, and including an intrinsic semiconductor layer including crystalline silicon grains making the surface of the intrinsic semiconductor layer toward the second electrode textured; and a second unit cell placed between the first unit cell and the second electrode.

A surface of a photovoltaic cell is coated with a solution that includes barium titanate to reduce reflection of sunlight that is incident on the surface. The solution may include a base of polydimethylsiloxane and carbon nanotubes. The process may be used in the fabrication of new photovoltaic cell assemblies, or to retrofit existing assemblies in situ.

Methods of forming a photovoltaic structures including nanoparticles are disclosed. The method includes electrospray deposition of nanoparticles. The nanoparticles can include TiO2 nanoparticles and quantum dots. In an example, the nanoparticles are formed on a flexible substrate. In various examples, the flexible substrate is light transparent. Photovoltaic structures and apparatus for forming photovoltaic structures are disclosed.

The present invention is realized by apparatus and methods for placing a large utility scale photovoltaic array in the low stratosphere of earth's atmosphere at an altitude of about 20 km, above clouds, moisture, dust, and wind. This is accomplished using a large light-weight, rigid, buoyant structure to support the large photovoltaic array. Long, strong and light tethers connect the buoyant structure to the ground and hold it in position against wind forces. The electricity output from the photovoltaic array is then coupled to high voltage transmission lines which connect from the platform to the earth's surface. The electricity is then transmitted through the high voltage transmission lines to the earth's surface where it is connected to the electrical supply grid and provides lower cost, more reliable electricity.

Methods for cleaning a side edge of a thin film photovoltaic substrate utilizing a laser are provided. The method can include transporting the substrate in a machine direction to move the substrate past a first laser source, and focusing a first laser beam generated by the first laser source onto the side edge of the substrate such that the laser beam removes the thin film present on the side edge of the substrate. An apparatus is also generally provided for cleaning a first side edge and a second side edge of a thin film photovoltaic substrate.

An adjustable photovoltaic panel mounting system that allows for variations in roofs and roof elements, while still maintaining a rigid and secure assembly. The specific location for supporting feet and structural elements of the mounting system may be varied to allow for variations in roof features and different panel configurations. The mounting mechanisms are adjustable in both a North/South and a East/West direction to provide for maximum layout flexibility.

The Lithuanian Business Support Agency (LSBA) has granted €235,000 (US$267,500) to support development of an experimental floating solar photovoltaic power plant at the existing 900-MW Kruonis pumped-storage hydroelectric plant in Lithuania.