LEF allows the same port with multiple shape definitions. Does anybody know if innovus can create multiple duplicate shapes associated with the same port? Assume they are connected outside the block with perfect timing synchronization. Thank you!

Hi there, 

we've encountered some strange behavior when trying to run the "check_litho" command from within INNOVUS 22.14. We set the required files and configuration files according to our PDK documentation. The command, without the absolute file paths, is:

check_litho -sign_off -cpu 96 -run_mode fg -create_guides -map_file <map file path> -config <config file path> -techfile <tech file path> -dir <output dir path> -write_stream_options "-mode ALL -merge <list of gds files>" -apply squishHints

We are currently using PEGASUSDFM 23.20 for this command but tested previous PEGASUSDFM and MVS versions as-well. After we issued the previous command, we see INNOVUS launching the PEGASUSDFM/MVS and trying to run the command. After some time, the command crashes with the error "mdb_load_with_extra: failed to pre-open extra input file './preproc/INTERMEDIATE.oas' for read". We have tested a similar setup with INNOVUS 19.10 where we did not have this issues. Did something change with the new INNOVUS version? Does anyone have an idea what we are missing? 

Thanks in advance.

Best regards,

PS

Hi everyone,

I'm designing a digital chip that will be fabricated. I have a HDL top module that includes several submodules inside it. I want to define the position of some of the submodules during the PnR so that later I can specify there positions in the Micrograph photo after the IC fabrication. When I perform the PnR using Innovus, I always got a layout shape where the submodules seems to be flatted. I wonder if there is a way to specify the placement of each submodule in my top module  (maybe in the tcl file) during the PnR so later I can define there positions in the micrograph photo. 

Thanks in Advance!

Hi everyone,

I'm new to using Innovus and I'm encountering an issue while trying to perform the "init_design" command. My goal is to perform the place and route. Here are the commands I'm using:

``
set init_verilog ./test.v
set init_top_cell TEST
set init_pwr_net {VDD VDD_2 VDD_3}
set init_gnd_net {VSS VSSA}
set init_lef_file { /home/laumecha/uw_openroad_free45/pdk/Drexel-ECEC575/Encounter/NangateOpenCellLibrary/Back_End/lef/NangateOpenCellLibrary.lef}
set init_mmmc_file {./viewDefinition.tcl}
init_design
```

However, I receive the following error:

```
#% Begin Load netlist data ... (date=06/04 12:07:50, mem=1478.7M)
*** Begin netlist parsing (mem=1439.0M) ***
Created 0 new cells from 0 timing libraries.
Reading netlist ...
Backslashed names will retain backslash and a trailing blank character.
**ERROR: (IMPVL-209):   In Verilog file './test.v', check line 16 near the text # for the issue: 'syntax error'.  Update the text accordingly.
Type 'man IMPVL-209' for more detail.
Verilog file './test.v' has errors!  See above.

*** Memory Usage v#1 (Current mem = 1439.027M, initial mem = 634.098M) ***
#% End Load netlist data ... (date=06/04 12:07:50, total cpu=0:00:00.0, real=0:00:00.0, peak res=1478.7M, current mem=1478.7M)
**ERROR: (IMPVL-902):   Failed to read netlist ./test.v. See previous error messages for details.  Resolve the issues and reload the design.
```

However, the file works perfectly in Genus.

It seems there is a syntax error in my Verilog file at line 16, but I'm not sure how to resolve it. Any guidance or suggestions would be greatly appreciated.

Thanks in advance!

Hi all,

I have been following the tutorial "Innovus Block Implementation with Stylus Common UI", version 23.1.

While I was doing the clock tree synthesis, the tutorial calls for a command

clock_opt_design

But my tool tells me this is a beta feature which needs to be enabled.

Warning: clock_opt_design requires beta feature innovusClockOptFlow enabled.

Can I ask how do I enable this beta feature?

My version of Innovus is v21.35-s114_1, is it because of the version incompatibility?

Many thanks

for debug I use suspend in my tcl script to debug，here is the code

after that the innovus command screen become 

how to quit the SUSPEND status？ thanks

Hi all, 

I have made a custom cell in Innovus that I will be instantiating into a bigger block, which I will also be using Innovus to do the Place & Route. 

I understand that I can generate a *.lef file and a *.lib file using Innovus. However, I need to also create a *.db file (these format of files are often used in DC Compiler synthesis tool). 

Is there a way to create the *.db file from Innovus? Or, is there a tool that I can use to create this *.db file? 

Thank you for your time. 

Hello All:

I am looking for help on the following, as I am new to Cadence tools [I have to use Cadence Innovus for Physical Design after Logic Synthesis using Synopsys Design Compiler, using Nangate 45 nm Open Cell Library]: while using Cadence Innovus, I would need to select a few specific nets to be routed through a specific metal layer. How can I do this on Innovus [are there any command(s)]? Also, would writing and sourcing a .tcl script [containing the command(s)] on the Innovus terminal after the Placement Stage of Physical Design be fine for this?

Secondly, is there a way in Innovus to manipulate layout components, such as changing some pin placements, wire directions (say for example, wire direction changed to facing east from west, etc.) or moving specific closely placed cells around (without violating timing constraints of course) using any command(s)/.tcl script? If so, would pin placement changes and constraining some closely placed cells to be moved apart be done after Floorplanning/Powerplanning (that is, prior to Placement) and the wire direction changes be done after Routing? 

While making the necessary changes, could I use the usual Innovus commands to perform Physical Design of the remaining nets/wires/pins/cells, etc., or would anything need modification for the remaining components as well?

I would finally need to dump the entire design containing all of this in a .def file.

I tried looking up but could only find matter on Virtuoso and SKILL scripting, but I'd be using Innovus GUI/terminal with Nangate 45 nm Open Cell Library. I know this is a lot, but I would greatly appreciate your help. Thanks in advance.

Riya

Please give me some ideas. Thank you very much.

How can I make innovus start with common UI instead of legacy? When I launch Innovus with command "innovus", I get the legacy UI. I have Innovus version 17.11 installed. 

Thanks in advance.

Hello,

I created a floorplan view in Virtuoso ( it contains pins and blockages). I am trying to run PnR in Innovus for floorplan created in Virtuoso. I used  set vars(oa_fp)    "Library_name cell_name view_name"   to read view from virtuoso. I am able to see pins in Innovus but not the blockages. Can i know how do i get the blockages created in virtuoso to Innovus.

Regards,
Amuu 

HI, I have been using the Innovus GUI commands for several things and wonder if those command can be written to a log or cmd file so I can use it in my flow script? Is there such options that we can set?

Thanks

Hi,

I am doing layout for a mixed-signal circuit in Innovus. I want to create a digital donut style of layout (i.e. put analog circuit in the middle, and circle analog part with digital circuits).

To do that, I need to place some pins inside the edge to connect to analog circuit (as shown in my attachment), but the problems is that I cannot place pins inside the edge by using "pin editor" within Innovus. Any suggestions to place pins inside?

Thank you so much for your time and effort.

Hi Everyone,

Many of you would have heard about the Cadence Stylus Common UI and are wondering what it is and what the advantages might be to use it versus legacy UI.

The webinar answers the following questions:

• Why did Cadence develop Stylus UI and what is Stylus Common UI?
• How does someone invoke and use the Stylus Common UI?
• What are some of the important and useful features of the Stylus Common UI?
• What are the key ways in which the Stylus Common UI is different from the default UI?​

If you want to learn more about Stylus UI in the context of implementation, view the 45-minute recorded webinar on the Cadence support site.

Related Resource

Innovus Block Implementation with Stylus Common UI

Vinita Nelson